FUJI错误代码查询 - 第77页

Group 3: Printing sequence Group 4: Snap-off, cleaning, inspection sequence ------------------------------ Code: 1101C1?? Display: Used by: CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643 Cause: Same as code (1101C100 + i/20) whe…

100%1 / 5282
------------------------------
Code: 1101C07F
Display:
Used by:
Cause: There are over 30 next devices and the loop does not close. This error applies to device numbers
301 to 500.
Remedy: Change the settings in "Next" in the production program so that the loop closes within 30
devices.
------------------------------
Code: 1101C080
Display:
Used by: IP3
Cause: The next device station is not the same as that of the original device. The original device is
between device number 1 and 50.
Remedy: Specify the correct device number in "Next" in the production program's D_data.
------------------------------
Code: 1101C081
Display:
Used by:
Cause: The next device station is not the same as that of the original device. The original device is
between device number 51 and 100.
Remedy: Specify the correct device number in "Next" in the production program's D_data.
------------------------------
Code: 1101C082
Display:
Used by:
Cause: The next device station is not the same as that of the original device. The original device is
between device nunber 101 and 300.
Remedy: Specify the correct device number in "Next" in the production program's D_data.
------------------------------
Code: 1101C083
Display:
Used by:
Cause: The next device station is not the same as that of the original device. The original device is
between device number 301 and 500.
Remedy: Specify the correct device number in "Next" in the production program's D_data.
------------------------------
Code: 1101C084
Display: Same as code
Used by: GP551,GP6
Cause: A speed has been set in the final cleaning sequence.
Remedy: Be sure to set a "-1" for the final cleaning sequence.
------------------------------
Code: 1101C085
Display: Same as code
Used by: GP551,GP6
Cause: Sequence error. Verify that the sequence groups are in the order shown below.
Remedy: Re-arrange the sequences so that the groups are in the proper order,then transfer the data. The
sequence order does not apply within the same group.
Group 1: Mask mark, board fiducial mark sequence
Group 2: Inspection reference sequence
第 76 页
Group 3: Printing sequence
Group 4: Snap-off, cleaning, inspection sequence
------------------------------
Code: 1101C1??
Display:
Used by: CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: Same as code (1101C100 + i/20) where i is the sequence number.
Remedy: The sequence references a device number 0 or less or greater than 140.
The device number that has been specified in sequence data is out of range
------------------------------
Code: 1101C2??
Display:
Used by: CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: Same as code (1101C200 + i/20) where i is the sequence number.
Remedy: The placing sequence's X data is out of the machine's range of movement.
There is a sequence where the X coordinate is outside the limits of the board in the X direction (PCB_X)
(single board production program).
------------------------------
Code: 1101C3??
Display:
Used by: CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643
Cause: Same as code (1101C300 + i/20) where i is the sequence number.
Remedy: The placing sequence's Y data is out of the machine's range of movement.
------------------------------
Code: 1101C400
Display: 1101C400
Used by: GSP5,GP2,GP3,GP551,GP6
Cause: There is an illegal combination of sequences in the production program.
Remedy: A production program must include two board fiducial sequences, two mask fiducial sequences
and two printing sequences. Check the production program sequences. As an exception it is possible to
transmit a program which contains only printing sequences.
------------------------------
Code: 1101C401
Display: 错误编码的编号无变动
Used by: GSP5,GP551,GP6,GPX
Cause: 生产程序中指定的印刷sequence超出规定范围。
Remedy: 请检查生产程序中的印刷sequence以及Proper的139.Max Limit Position S Holder, 140.Min Limit
Position S Holder。
印刷可设置范围：
(GPX V5.40以上)
·第1个sequence:－15.00mm～电路板尺寸Y
当第1个sequence的起点在电路板外围时
请将第二个sequence的起点设置为0.00mm；剩余印刷区域请从第3个sequence开始依次进行设置。
如果第1个sequence的印刷范围是0.01mm～电路板尺寸Y，
则请将之后的sequence都设置为上一个sequence的终点～电路板尺寸Y。
·最后一个sequence:电路板尺寸Y～电路板尺寸Y＋15.00mm
最后一个sequence需要印刷电路板外围时
最后第2个sequence的数值与电路板尺寸Y必须保持一致。
(GPX V5.30以前)
·第1个sequence:1mm～电路板尺寸Y
·第2～第9个sequence:上一个sequence的终点～电路板尺寸Y
第 77 页
·第10个sequence：电路板尺寸Y。
------------------------------
Code: 1101C402
Display: 印刷顺序的印刷位置指定错误
Used by: NXTP
Cause: Flexa上印刷顺序的设定值超过公差值。
Remedy: ·请指定起点和终点。
·一侧最大可以指定10个顺序。
·请设定次顺序的值大于前顺序的值。
·位置的最小值和最大值在范围外(虽然印刷范围受其他参数的影响为可变数值，但是0～电路板尺寸为止为可印刷范围)
------------------------------
Code: 1101C403
Display: 印刷顺序的印刷位置指定错误
Used by: NXTP
Cause: Flexa上的印刷顺序的两侧印刷的指定方法超出公差值。
Remedy: ·请在Front侧和Rear侧上设定相同数量的印刷位置。
·请在Front侧和Rear侧上设定相同位置的印刷位置。
------------------------------
Code: 1101C404
Display: 印刷sequence的印刷范围延伸设置错误
Used by: GPX
Cause: 印刷sequence的印刷范围延伸设置不正确。
Remedy: 请确认生产程序中的印刷sequence。
如果第1个sequence的起点在电路板外围，
则请将第二个sequence的起点设置为0.00mm。
如果最后一个sequence需要印刷电路板外围，
则最后第2个sequence的数值与电路板尺寸Y必须保持一致。
------------------------------
Code: 1101C405
Display: 印刷sequence的数量设置错误
Used by: GPX
Cause: 印刷sequence的数量未设置或超出规定范围。
Remedy: 单侧最多可设置10个sequence。如果按印刷方向进行设置，则Front和Rear的数量和位置都必须相同。
------------------------------
Code: 1101C406
Display: 印刷sequence的数量设置错误
Used by: GPX-C
Cause: 在Flexa中设置的印刷sequence(Print Solder)有误。
Remedy: (Fig.1)如果印刷sequence不设置任何数值，则可以以默认值进行印刷。(Fig.2)如果设置印刷sequence，则
请设置2个点(起点和终点)。(Fig.3)如果按印刷方向设置印刷sequence，则请设置4个点(起点和终点×2)在这种情形下
，请将起点和终点位置设置为相同数值。(Fig.4)设置时数值可以超出电路板尺寸。(以电路板尺寸Y=150mm为例)
<img src="$LKEY_ERRIMG_MC$/1101C406.jpg">
------------------------------
Code: 1101C407
Display: 「印刷sequence」项目中的印刷位置设置错误
Used by: GPX
Cause: 代表位置的最小值、最大值超出规定范围。
Remedy: 代表印刷允许范围的数值会受其它参数的影响而变动。
------------------------------
Code: 1101C408
Display: 「印刷sequence」项目中的印刷位置设置错误
第 78 页