FUJI错误代码查询 - 第878页
Remedy: The servo controller could be damaged. Obtain the trace data and contact Fuji. ------------------------------ Code: 12110074 Display: SERCOS communication error. Used by: Cause: An error has occurred during IDN S…
Remedy: Check to ensure that the soft limit position and calibration data is correct.
------------------------------
Code: 1211006c
Display: Overtravel error.
Used by:
Cause: A positive overtravel condition was detected.
Remedy: Ensure that there are no breaks in the sensor wiring,
Check the machine calibration data to ensure that it is correct.
------------------------------
Code: 1211006d
Display: Soft limit error.
Used by:
Cause: A soft positive overtravel condition was detected.
Remedy: Check to ensure that the soft limit position and calibration data is correct.
------------------------------
Code: 1211006e
Display: Abnormal servo amplifier error.
Used by:
Cause: A servo amplifier alarm occurred.
Remedy: Check the cause of the servo alarm and that the appropriate measurement has been made. If
this occurs frequently after turning on the power, contact Fuji.
------------------------------
Code: 1211006f
Display: Abnormal encoder error.
Used by:
Cause: The encoder information between the amplifier and the servo controller is abnormal.
Remedy: Ensure that there are no breaks in the encoder wiring.
------------------------------
Code: 12110070
Display: 12V power loss.
Used by:
Cause: The 12V power supply for the servo control board was cut off.
Remedy: Check to ensure that the wire for the power supply is not broken or disconnected.
------------------------------
Code: 12110071
Display: Home signal detected.
Used by:
Cause: The home signal was detected and stop processing was performed.
Remedy: Check to ensure that the parameters in the servo initialization file are correct.
Make sure that the signal wire for the speed reduction sensor is not broken or disconnected.
------------------------------
Code: 12110072
Display: Amplifier parameter modified.
Used by:
Cause: An amplifier parameter has been changed.
Remedy: Reboot the machine in order to use the changed parameters.
------------------------------
Code: 12110073
Display: Servo controller error.
Used by:
Cause: An error has occurred in the processing performed for the servo controller board.
第 877 页
Remedy: The servo controller could be damaged. Obtain the trace data and contact Fuji.
------------------------------
Code: 12110074
Display: SERCOS communication error.
Used by:
Cause: An error has occurred during IDN SERCOS communication.
Remedy: Ensure that the digital operator is not connected to an amplifier. If this error cannot be
corrected, obtain the trace data and contact Fuji. In such a situation, the SERCOS drive could be
damaged.
------------------------------
Code: 12110075
Display: Zero setting error.
Used by:
Cause: An invalid zero setting type is specified.
Remedy: Reinstall the software, because the initial installation could have failed.
------------------------------
Code: 12110076
Display: Axis movement processing error.
Used by:
Cause: During axis movement, another process occurred.
Remedy: Reinstall the software, because the initial installation could have failed.
------------------------------
Code: 12110077
Display: Servo parameter error.
Used by:
Cause: Failed to set a parameter on the servo controller board.
Remedy: Reinstall the software, because the initial installation could have failed.
If this error cannot be corrected, obtain the trace data and contact Fuji. In such a situation, the
servo controller board could be damaged.
------------------------------
Code: 12110078
Display: Servo parameter error.
Used by:
Cause: Failed to acquire a servo parameter from the servo controller board.
Remedy: Reinstall the software, because the initial installation could have failed.
If this error cannot be corrected, obtain the trace data and contact Fuji. In such a situation, the
servo controller board could be damaged.
------------------------------
Code: 12110079
Display: Compare position registration error.
Used by:
Cause: The specified compare position object is not registered.
Remedy: Reinstall the software, because the initial installation could have failed.
If this error cannot be corrected, obtain the trace data and contact Fuji.
------------------------------
Code: 1211007a
Display: SERCOS communication error.
Used by:
Cause: An error occurred during SERCOS communication.
Remedy: Ensure that the digital operator is not connected to an amplifier. If this error cannot be
corrected, obtain the trace data and contact Fuji. In such a situation, the SERCOS drive could be
第 878 页
damaged.
------------------------------
Code: 1211007b
Display: Machine type error.
Used by:
Cause: This function can only be called in a machine with an analog environment.
Remedy: Reinstall the software, because the initial installation could have failed.
If this error cannot be corrected, obtain the trace data and contact Fuji.
------------------------------
Code: 1211007c
Display: Machine type error.
Used by:
Cause: This function can only be called in a machine with an SERCOS environment.
Remedy: Reinstall the software, because the initial installation could have failed.
If this error cannot be corrected, obtain the trace data and contact Fuji.
------------------------------
Code: 1211007d
Display: Movement interpolation error.
Used by:
Cause: Movement interpolation has occurred for the same axis.
Remedy: Reinstall the software, because the initial installation could have failed.
If this error cannot be corrected, obtain the trace data and contact Fuji.
------------------------------
Code: 1211007e
Display: Movement interpolation error.
Used by:
Cause: For the selected axes, movement interpolation cannot be be done because the axes are not on the
same servo controller board.
Remedy: Reinstall the software, because the initial installation could have failed.
If this error cannot be corrected, obtain the trace data and contact Fuji.
------------------------------
Code: 1211007f
Display: Process error.
Used by:
Cause: A function only supported by the RTX process was called.
Remedy: Reinstall the software, because the initial installation could have failed.
If this error cannot be corrected, obtain the trace data and contact Fuji.
------------------------------
Code: 12110080
Display: Process error.
Used by:
Cause: A function only supported by the Win32 process was called.
Remedy: Reinstall the software, because the initial installation could have failed.
If this error cannot be corrected, obtain the trace data and contact Fuji.
------------------------------
Code: 12110081
Display: Axes stop demand.
Used by:
Cause: The axis movement was stopped by the application.
Remedy: Remove the cause of the error and resume operation.
------------------------------
第 879 页