FUJI错误代码查询 - 第885页
Used by: Cause: A file required cannot be found. The required file could either be corrupted or may have been deleted. Remedy: Reinstall the system. If the same error occurs after the reinstallation, the hard disk could …
------------------------------
Code: 12200004
Display: Failed to create thread.
Used by:
Cause: Either the system resources are insufficient, the operating system is corrupted, or the operating
system installation failed.
Remedy: Reinstall the recovery media software if this error cannot be corrected, because the hard disk
could be damaged.
------------------------------
Code: 12200005
Display: Failed to create event.
Used by:
Cause: Either the system resources are insufficient, the operating system is corrupted, or the operating
system installation failed.
Remedy: Reinstall the recovery media software if this error cannot be corrected, because the hard disk
could be damaged.
------------------------------
Code: 12200006
Display: Failed to create semaphore.
Used by:
Cause: Either the system resources are insufficient, the operating system is corrupted, or the operating
system installation failed.
Remedy: Reinstall the recovery media software if this error cannot be corrected, because the hard disk
could be damaged.
------------------------------
Code: 12200007
Display: Event creation abnormal.
Used by:
Cause: From the RTX process, Win32 event creation was abnormal. It is possible that the system
installation failed.
Remedy: Reinstall the system. If this error is not corrected after the reinstall, the servo controller could be
damaged.
------------------------------
Code: 12200008
Display: Semaphore creation abnormal.
Used by:
Cause: From the RTX process Win32 semaphore creation was abnormal. It is possible that the system
installation failed.
Remedy: Reinstall the system. If this error is not corrected after the reinstall, the servo controller could be
damaged.
------------------------------
Code: 12200009
Display: Process creation abnormal.
Used by:
Cause: From the RTX process Win32 process creation was abnormal. It is possible that the system
installation failed.
Remedy: Reinstall the system. If this error is not corrected after the reinstall, the servo controller could be
damaged.
------------------------------
Code: 1220000a
Display: Missing file.
第 884 页
Used by:
Cause: A file required cannot be found. The required file could either be corrupted or may have been
deleted.
Remedy: Reinstall the system. If the same error occurs after the reinstallation, the hard disk could be
damaged.
------------------------------
Code: 1220000b
Display: Synchronize object error.
Used by:
Cause: Object synchronization was not completed. The system resources are insufficient, the operating
system is corrupted, or the operating system installation failed.
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the hard disk could be
damaged.
------------------------------
Code: 1220000c
Display: Process not ended.
Used by:
Cause: Processing was not completed. The system resources are insufficient, the operating system is
corrupted, or the operating system installation failed.
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the hard disk could be
damaged.
------------------------------
Code: 1220000d
Display: Missing RT process load.
Used by:
Cause: The required file is either corrupted or may have been deleted.
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the hard disk could be
damaged.
------------------------------
Code: 1220000e
Display: Failed to create object.
Used by:
Cause: Failed to create the servo driver control object, or the servo controller device driver file is
corrupted.
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the servo control board
could be damaged.
------------------------------
Code: 1220000f
Display: Firmware does not match.
Used by:
Cause: The version check performed after a servo control board firmware upgrade has found that the
version does not match.
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the servo control board
could be damaged.
------------------------------
Code: 12200011
Display: Failed to access the firmware.
Used by:
Cause: Failed to access the servo control firmware, or the servo controller device driver is corrupted.
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the servo control board
could be damaged.
第 885 页
------------------------------
Code: 12200012
Display: Firmware check error.
Used by:
Cause: An error was detected when performing a servo control firmware check, or the servo controller
device driver is corrupted.
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the servo control board
could be damaged.
------------------------------
Code: 12200013
Display: Firmware overwritten.
Used by:
Cause: The servo control firmware has been overwritten. This occurs for certain versions after
immediately upgrading. This error occurs frequently after booting up the machine when the flash memory
is damaged.
Remedy: If this error occurs only one time after upgrading, there is no problem.
If this error occurs frequently, the servo control board could be damaged.
------------------------------
Code: 12200014
Display: Firmware error.
Used by:
Cause: The servo control firmware name is not specified.
It is possible that the servo initialization file is corrupted, an incorrect setting has been specified,
or the servo controller device driver is corrupted
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the hard disk could be
damaged.
------------------------------
Code: 12200015
Display: Linear encoder.
Used by:
Cause: An unexpected error occurred while confirming the linear encoder connection, or the servo
controller device driver is corrupted.
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the servo control board
could be damaged.
------------------------------
Code: 12200016
Display: Linear encoder error.
Used by:
Cause: The linear encoder connection check detected an inappropriate encoder.
Some other encoder is connected to the axis with the linear encoder setting, or the dip switch
setting for the machine is incorrect.
Remedy: Check the connection for the linear encoder. Ensure that the dip switch and amplifier settings
are correct.
------------------------------
Code: 12200017
Display: Initialization failed.
Used by:
Cause: Failed to initialize servo controller access, or the servo controller device driver is corrupted.
Remedy: Reinstall the recovery media software. If this error cannot be corrected, the servo control board
could be damaged.
------------------------------
第 886 页