wire-bonder.pdf - 第34页
WEST•BOND MODEL 454647E SER IES INSTRUCTION MANUAL 28 OPERATION Work Height Elevation Before any new part is to be programmed, or run for the first time, the work elevation needs to be verified. This is so that the searc…
WEST•BOND MODEL 454647E SERIES INSTRUCTION MANUAL
27
OPERATION
Align Menu 2
This menu is used for scanning the other bonds or changing the Y Offsets. The purpose is to verify all the
bond positions to decide whether the station needs to be rotated or not; since bonding motion is straight-
front-to-back.
SCAN BOND 2 of 2: 120 from Bond 1
5=Increase (0.02500”)
7=Prev bond 8=Y restore 9=Next bond
A=Prev menu 0=Decrease G=OK
The X-Y Manipulator is Locked. Use 5 or 0 to adjus
t
the Bond position.
N
OTE! 120 is an example of Y offset position, thi
s
number will be updated to a permanent number when
the G key is pressed if the new number is different.
ϑ To call “Align Menu 2”
From the H
OME menu press 8 (MORE OPTIONS) and then press 9 (SCAN BONDS)
Key Format:
1
2
Home
3
4
Increase
5
6
Previous
bond
7
Restore
8
Next bond
9
Previous
menu
A
Decrease
0
OK
G
SCAN BOND
Device 1, Type 1: (2 Bonds)
-->USE MANIPULATOR TO ALIGN TV CROSSHAIR
TO BOND 1 AND PRESS 9 WHEN READY
Y OFFSET of Bond #1: Always 0
7=Move XY 9=Next bond
A=Prev menu
Bond 1 is not moveable. Use key 7 to realign the TV
crosshairs to bond 1 if not centered on Bond 1.
WEST•BOND MODEL 454647E SERIES INSTRUCTION MANUAL
28
OPERATION
Work Height Elevation
Before any new part is to be programmed, or run for the first time, the work elevation needs to be verified.
This is so that the search elevations and the looping heights will be correct, and no damage to the tool will
occur.
Restart Height Elevation: 1400 from top
Suggested setting is 800 for 4700E Mode.
4=Key in 5=Up (0.29167”)
7=Work Height 8=Suggest
A=Prev Option 0=Down G=Next Option
== WORK HEIGHT VERIFICATION ==
(Look in microscope)
Tool will run down during this mode.
Select the median bond height & Press G
Select a bond area that will be in the
middle of the bond range and press G.
Adjust the Table according to the LCD.
ϑ To call “Work Verification Menu”
At the H
OME menu press 4 (EDIT), 6 (MACHINE), 9 (RESTART HEIGHT), and then 7 (WORK
HEIGHT VERIFICATION)
Key Format:
Previous
menu
1
Go To
Device/Type
2
Home
3
Key In
4
↑ Y up
5
6
Work
Height
7
Suggest
8
9
Previous
Option
A
↓ Y down
0
Next
Option
G
WEST•BOND MODEL 454647E SERIES INSTRUCTION MANUAL
29
OPERATION
Full-Auto Bonding
The bonding sequence continues without operator intervention until the completion of one complete wire
run. The operator may stop bonding in this mode by pressing any key.
FULL-AUTO BONDING (G was pressed in the Align or “Home” menu, or from Manual Bonding)
Bond 1 of 5 -->Look in microscope.
Force: Low Power: 240 Time: 20ms
-> Any key halts bonding
(hold until activity stops).
ϑ To change from “Half-Auto” Mode to “Full-Auto” Mode
From the H
OME menu press the 8 key twice.
Key Format:
Manual
Bond
1
Manual
Bond
2
Manual
Bond
3
Manual
Bond
4
Manual
Bond
5
Manual
Bond
6
Manual
Bond
7
Manual
Bond
8
Manual
Bond
9
Manual
Bond
A
Manual
Bond
0
Manual
Bond
G