wire-bonder.pdf - 第66页

WEST•BOND MODEL 454647E SER IES INSTRUCTION MANUAL 60 ADVANCED PROGRAMMING Low Force This screen will only be displayed if the operator has selected the D UAL F ORCE option. Having selected O N for the D UAL F ORCE optio…

100%1 / 126
WEST•BOND MODEL 454647E SERIES INSTRUCTION MANUAL
59
ADVANCED PROGRAMMING
Force Adjust
This option allows the operator to calibrate the HIGH FORCE setting by simply adjusting the force
adjustment knob. This A
DJUSTMENT KNOB is located to the right of the tool head assembly (see picture on
the next page). To increase the bond force, turn the knob counter-clockwise (CCW). To decrease the
bond force turn the knob clockwise. To determine the force for bonding use a gram gauge as illustrated in
the picture below. Lift the tooling head, Just in front of the Bonding Tool, with the gram gauge. The
system will signal the operator when the firing switch opens, This will signify the High Force setting.
HIGH FORCE (Displayed if Dual Force is On)
CALIBRATE HIGH FORCE
Use force gage to measure Calibration
Force at the tool.
A=Prev option G=Next option
FORCE (Displayed if Dual Force is Off)
CALIBRATE FORCE
Use force gage to measure Calibration
Force at the tool.
A=Prev option G=Next option
ϑ To edit “High Force” (If Dual Force is ON) or “Force” (If Dual Force is OFF)
From the H
OME menu press 4 (EDIT), 6 (MACHINE), and then 8 (FORCE ADJUST)
Key Format:
1
2
Home
3
4
5
6
7
8
9
Previous
option
A
0
Next option
G
WEST•BOND MODEL 454647E SERIES INSTRUCTION MANUAL
60
ADVANCED PROGRAMMING
Low Force
This screen will only be displayed if the
operator has selected the DUAL FORCE
option. Having selected O
N for the DUAL
FORCE option, the operator is allowed to
calibrate the low force setting while at this
menu.
The operator should expect to hear the air
cylinder activate when entering this menu.
The air cylinder will deactivate when leaving
this menu.
R
EMINDER: This menu is used for calibrating
or establishing the L
OW FORCE setting.
To Adjust the L
OW FORCE setting, loosen the
knurled L
OCK NUT and turn the knurled
PLUNGER ADJUSTMENT KNOB located on the
opposite end of the HIGH FORCE knob. Use
the gram gauge to determine the L
OW FORCE
setting. See page 82 for details on how to
select High or Low force for individual bonds.
LOW FORCE (Displayed if Dual Force is On)
CALIBRATE LOW FORCE
Use force gage to measure Calibration
Force at the tool.
A=Prev option G=Next option
ϑ To edit “Low Force” (If Dual Force is ON) or “Force” (If Dual Force is OFF)
From the H
OME menu press 4 (EDIT), 6 (MACHINE), 8 (FORCE ADJUST), then G (SEQUENCE)
Key Format:
1
2
Home
3
4
5
6
7
8
9
Previous
option
A
0
Next option
G
WEST•BOND MODEL 454647E SERIES INSTRUCTION MANUAL
61
ADVANCED PROGRAMMING
Restart Height
RESTART HEIGHT ELEVATION
Restart Height Elevation: 1400 from top
4=Key in 5=Up (0.29167”)
7=Work height 8=Suggest
A=Prev option 0=Down G=Next option
800 is the suggested elevation for the 4700E
Programmed in Z Motor half-steps from home
7=Work Height Verification (see page 28)
Key Format:
Previous
Menu
1
2
Home
3
Key in
4
↑
Up
5
6
Work height
7
Suggest
8
9
Previous
option
A
↓
Down
0
Next option
G
ϑ To edit “Restart Height Elevation”
From the H
OME menu press 4 (EDIT), 6 (MACHINE), and then 9 (RESTART HT).