00195170-01 SA trailing cable - 第13页

Replacing the Trailing Cable Unit [03039709-xx] Conversion on SIPLACE HF Machines up to A 219 Service Manual Exchange of the trailing cable SIPLACE HF and X-Series 13 2.4 Conversion on SIPLACE HF Machines up to A 219 The…

Replacing the Trailing Cable Unit [03039709-xx]

Installation

12 Service Manual Exchange of the trailing cable SIPLACE HF and X-Series

X Fit the gantry interface board onto the cable

holder (4) of the new trailing cable unit.

X Fasten the trailing cable console (1) loosely

with a screw.

X Clean the trailing cable contact surface on the

machine base with a dry cloth.

X Starting from the trailing cable console (1), run

the flat ribbon cable and hoses to the relevant

connections:

 Pneumatic distributor (2)

 Trailing cable interface (3)

 Gantry interface (4)

 Gantry distributor (5)

X Reconnect to the electrical system. Observe

the correct connector assignment.

X Shorten the compressed air hoses to the opti-

mum length, making sure that they are not too

short or long. They must engage firmly but

should not buckle.

X Reconnect to the compressed air supply. Ob-

serve the correct connector assignment.

X Fasten the pressure plates (6) loosely to the

machine base.

X Check that the power track chain can run alo-

ng the top of the machine base without ob-

struction. Move the Y-axis back and forth to

check this.

X Correct at the trailing cable console (1) and at

the pressure plates, where necessary.

X Fix the two pressure plates (6) and the trailing

cable console (1). Use Loctite 241 locking

paint.

X Tighten the trailing cable console (1) fastening

screws crosswise.

Replacing the Trailing Cable Unit [03039709-xx]

Conversion on SIPLACE HF Machines up to A 219

Service Manual Exchange of the trailing cable SIPLACE HF and X-Series

2.4 Conversion on SIPLACE HF Machines up to A 219

These versions of the trailing cable unit can also be used for SIPLACE HF machines up to machine num-

ber A-219 in combination with the "retrofitting set for trailing cable" 03046248-01.

 Trailing cable unit for HF machines with one gantry

– 03039706S01 analog trailing cable unit 1P

 Trailing cable unit for HF machines with two gantries at uneven locations (1 and 3)

– 03039708S01 analog trailing cable unit 2P U

 Trailing cable unit for HF machines with two gantries at even locations (2 and 4)

– 03039709S01 analog trailing cable unit 2P G

X Reconnect the cooling tubes to the Y-axis mo-

tor.

X Install the 3 pressure plates (1) to the gantry

and the head mount (2).

X You will need to replace the cable supports on

SIPLACE HF machines up to machine number

MA219. See also Section 2.4 Conversion on

SIPLACE HF Machines up to A 219 [J 13].

X Fit the head board (3). Make sure you do not

lose the contact disks or spacer bolts.

X Plug in all connections/terminals. Observe the

correct connector assignment.

X Fasten new cable ties at the original points.

X Replace all cover plates.

The new pressure plate is no longer fastened to

the existing cable supports. Therefore, the old ca-

ble supports (1) need to be replaced.

X Replace the old cable supports (1) with the

new cable supports (2) from the retrofitting set.

The new cable supports have 4 drillings (3) to

fix the new pressure plate.

Replacing the Trailing Cable Unit [03039709-xx]

Conversion on SIPLACE HF Machines up to A 219

14 Service Manual Exchange of the trailing cable SIPLACE HF and X-Series

X Fit the pressure plate for the new trailing cable

unit onto the new cable supports, with the 4

M3x35 screws from the retrofitting set.

X If the pressure plate does not fit into the exi-

sting drillings on the gantry, loosen the pressu-

re plate clamp and adjust it.

X Tighten the clamp again and fit the pressure

plate onto the gantry drillings.