00195170-01 SA trailing cable - 第6页
Introduction Handling the Hose Unlocking Device [0304709 0-xx] 6 Service Manual Exchange of the trai ling cable SIPLACE HF and X-Series – 03002306-03 digi tal trailing cable unit 2P U Trailing cable unit for X-se ries …
Introduction
SIPLACE HF Models
Service Manual Exchange of the trailing cable SIPLACE HF and X-Series
5
1Introduction
This service manual describes the installation and removal of the trailing cable unit for Siplace HF and
X series machines in their various models.
The manual sometimes uses diagrams of the SIPLACE HF machine. However, this does not necessarily
mean that installation or removal differs from this for the X-series machines. If there are any significant
differences between procedures for the two machine types, these will always be clearly shown with the
respective diagram.
1.1 SIPLACE HF Models
Trailing cable unit for HF machines up to series number A-219
There are three different trailing cable units available for SIPLACE HF machines. The version used
depends on the gantry arrangement in your machine.
Trailing cable unit for HF machines with one gantry
– 03009210-01 trailing cable analog 1P
Trailing cable unit for HF machines with two gantries at uneven locations (1 and 3)
– 03013642-03 trailing cable analog 2P U
Trailing cable unit for HF machines with two gantries at even locations (2 and 4)
– 03013940-03 trailing cable analog 2P G
Trailing cable unit for HF machines from series number A-220 onwards
There are three different trailing cable units available for SIPLACE HF machines. The version used de-
pends on the gantry arrangement in your machine.
Trailing cable unit for HF machines with one gantry
– 03039706S01 analog trailing cable unit 1P
Trailing cable unit for HF machines with two gantries at uneven locations (1 and 3)
– 03039708S01 analog trailing cable unit 2P U
Trailing cable unit for HF machines with two gantries at even locations (2 and 4)
– 03039709S01 analog trailing cable unit 2P G
1.2 SIPLACE X-Series Models
Trailing cable unit for X-series machines up to series number B-078
There are three different trailing cable units available for SIPLACE X-series machines. The version used
depends on the gantry arrangement in your machine.
Trailing cable unit for X-series machines with one gantry
– 03015419-03 digital trailing cable unit 1P U
Trailing cable unit for X-series machines with two gantries at uneven locations (1 and 3)
NOTE: Backwards compatibility
These versions of the trailing cable unit can also be used for SIPLACE HF ma-
chines up to machine number A-219 in combination with the "retrofitting set for
trailing cable" 03046248-01. This set is included in the trailing cable spare parts
package.
X Fit the new X-cable support.
Introduction
Handling the Hose Unlocking Device [03047090-xx]
6 Service Manual Exchange of the trailing cable SIPLACE HF and X-Series
– 03002306-03 digital trailing cable unit 2P U
Trailing cable unit for X-series machines with two gantries at even locations (2 and 4)
– 03003199-03 digital trailing cable unit 2P G
IGUS trailing cable unit for X-series machines from series number B-079 onwards
There are three different trailing cable units available for SIPLACE X-series machines. The version used
depends on the gantry arrangement in your machine.
Trailing cable unit for X-series machines with one gantry
– 03022236-01 digital trailing cable unit 1P
Trailing cable unit for X-series machines with two gantries at uneven locations (1 and 3)
– 03022237-01 digital trailing cable unit 2P U
Trailing cable unit for X-series machines with two gantries at even locations (2 and 4)
– 03021065-01 digital trailing cable unit 2P G
1.3 Handling the Hose Unlocking Device [03047090-xx]
NOTE: No backwards compatibility
These versions of the trailing cable unit can not be used for SIPLACE X-series
machines up to machine number A-078.
Since access to the pneumatic distributor at the
gantry is difficult, we recommend that you use the
unlocking device.
The hose unlocking device [03047090-xx] helps
you to open the unlocking ring (shown in blue he-
re) for the pneumatic connection and remove both
the hoses and the dummy plugs (additional tool
included in set).
X Open the unlocking ring with the pipe-shaped
part of the tool (1) .
X Pull the hose out of the pneumatic connection.
The diagram shows the removal of a dummy
plug (2) and not of a hose.
Replacing the Trailing Cable Unit [03039709-xx]
Service Manual Exchange of the trailing cable SIPLACE HF and X-Series
7
2 Replacing the Trailing Cable Unit [03039709-xx]
Parts
Analog trailing cable unit 1P [03039706-01]
Analog trailing cable unit 2P U [03038708-01]
Analog trailing cable unit 2P G [03039709-01]
Hose nippers for cutting the compressed air hoses
Pipe/hose cutters [00381443-01]
Hose unlocking device [03047090-xx]
Loctite 241 [02101037-01]
Preparation
The trailing cable unit is supplied as a complete assembly. Depending upon the configuration of the ma-
chine, you will need to remove the relevant modules, covers and cover plates before you can dismantle
the trailing cable.
See also:
J 2.4 Conversion on SIPLACE HF Machines up to A 219 [J 13]
X Where necessary, remove the cover plates
from the gantry trailing cable. Mark their exact
position to ensure correct replacement later.
X Remove the top central cover from the SIPLA-
CE machine.
X Remove the upright EMC plates so that you
can reach the trailing cable.