WPC4 services manual - 第11页
Operational Safety Safety Instructions for the Compressed Air Supply Safety Instructions Service Manual SIPLACE WPC4 11 2.2.3 Safety Instructions fo r the Compressed Air Supply 2.2.4 Safety Instructions for W o rking wit…
Operational Safety
Safety Instructions Safety Instructions for the Power Supply
10 Service Manual SIPLACE WPC4
2.2.2 Safety Instructions for the Power Supply
Consequently, parts of the system carry potentially lethal voltages, even when it is switched off at
the main switch.
Incorrect handling of the placement system can therefore result in death, severe injury or
considerable damage to equipment.
Measurements and repairs must always be carried out by appropriately qualified personnel.
Always follow the applicable accident prevention and VDE regulations (particularly DIN EN 60 204,
part 1) or the regulations specific to your country.
Before starting any repairs, switch off at the main switch and disconnect the placement system from
the main power supply.
Always secure the machine against unauthorized reactivation. If these instructions are not followed,
it is possible to touch live parts, which could result in death or severe injury.
Exchanging components
X End all placement operations on the placement system.
X Shut down the Windows NT operating system correctly, otherwise problems may occur when
restarting or data may be lost.
X Switch the placement system off at the main switch.
X Disconnect the placement system from the main power supply.
X Switch off the machine and attach warnings signs to indicate that service work is in progress.
2.2.2.1 Safety Instructions for Work on the Cutting Device
WARNING: Hazardous voltages!
The machine is supplied with 3 x 400 V~ (or 3 x 204 V~ / 3 x 230 V~ / 3 x 380 V~ / 3 x 415 V~)
± 5 %, 50/60 Hz mains voltage.
X Please observe the safety instructions in the Operating Manual for all service work!
WARNING: Risk of injury when working near the cutter.
If you wish to work on the tape cutter, you must disconnect the machine from the mains supply
and compressed air supply.
X Wait until the operating pressure has dropped to 0 MPa.
X Always secure the machine against unauthorized reactivation.
X Wear appropriately thick protective gloves when working near the blades/the tape deflector!
X There is a high risk of injury from stationary blades and moveable blades and from the tape
deflector of the cutter, even when the machine has been turned off!
X Never reach into the pneumatic cutter from below or into the empty-tape duct from above, not
even to resolve a problem (e.g. when tape is jammed).
CAUTION: Risk of injury when performing service work on the cutter.
Never support the cutter on your body (e.g. on your knee or thighs). Do not place your feet under
it.
X Wear appropriately thick protective gloves.
X When removing the cutter, hold it only on the left and right, on the outside.
X Make sure that no one can injure themselves on the cutter after it has been dismantled!
Operational Safety
Safety Instructions for the Compressed Air Supply Safety Instructions
Service Manual SIPLACE WPC4
11
2.2.3 Safety Instructions for the Compressed Air Supply
2.2.4 Safety Instructions for Working with Strong Magnetic Fields
CAUTION: Risk of injury from compressed air!
Risk of injury when disconnecting the compressed air lines.
X NEVER disconnect compressed air lines while they are still pressurized.
ATTENTION: Prolonged interruptions to the compressed air supply can cause damage.
When the machine is switched on, do not use the stop valve to interrupt the compressed air
supply for more than 30 minutes.
X If you need to shut off the compressed air system for longer, in order to carry out maintenance
or servicing work, you must switch the placement system off at the main switch and
disconnect it from the power supply.
WARNING: STRONG MAGNETIC FIELDS
Fatal hazard: persons with active implants (e.g. pacemakers, defibrillators, insulin pumps etc.)
are at risk from strong permanent magnetic fields inside the machine.
Persons are risk should avoid the immediate vicinity of the machine.
CAUTION: DANGER OF CRUSHING
Risk of crushing/trapping for persons with passive metal implants (e.g. plates, screws).
X Do not reach or lean over into the machine when the protective cover is open.
X Do not bring any metal objects into the area.
ATTENTION: STRONG MAGNETIC FIELDS
There is a risk that the strong magnetic fields could corrupt data on data media or credit
controller boards and check controller boards.
X Keep sensitive data carriers away from the permanent magnets.
Operational Safety
Safety Instructions Safety Instructions for Working with Strong Magnetic Fields
12 Service Manual SIPLACE WPC4