00192790-01 - 第35页
User Manual SIPLAC E S-25 HM / HS-50 2 PCB Camera Mu lticolor (Option) Software Version S C.502.xx 11/00 Issue 2.3 Focus Heigth: Install/Remove the Distance Plate 35 PPZ LWKRXW GLVW DQFHSODWH %277 20( '*…
2 PCB Camera Multicolor (Option) User Manual SIPLACE S-25 HM / HS-50
2.3 Focus Heigth: Install/Remove the Distance Plate Software Version SC.502.xx 11/00 Issue
34
&KHFNLQJWKH6XEVWUDWH7KLFNQHVVDQG$GDSWLQJWKH)RFXV+HLJKW
Whenever the current thickness of substrate or PCB is changed, you must check whether the dis-
tance plate (= spacer) must be installed under the PCB camera Multicolor or removed , as shown
in Fig. 2.3 - 7.
This check can be carried out either on the basis of the table (see above) or, without calculation,
by querying from the line computer (-> Job editor -> Services -> Error messages), as described in
detail in the User Manual for the UNIX line computer SW V502.xx, Section "Configuration of the
PCB camera Multicolor at the Line Computer").
When installed, the space plate is NOT visible. To ascertain whether the spacer place is currently
installed or not, it is therefore necessary to measure the actual distance between the bottom edge
of the PCB camera and the top edge of the conveyor belt (= bottom edge of PCB), as described
below.
Å Determine how thick the PCB or substrate to be processed actually is.
Å Use the above table to determine whether the distance plate is required or not.
Å Use the sliding calipers to determine the actual distance between the bottom edge of the PCB
camera Multicolor and the bottom edge of the camera holder as shown in Fig.2.3 - 1 and
Fig.2.3 - 2.
Å If a change must be made, remove the PCB camera Multicolor starting from the bottom of the
gantry, proceeding as described below beginning with "Preparatory Steps".
The allocation of camera and gantry must be preserved.
If you detach all the camera´s electrical connections (NOT necessary for this work), you must
use a permanent marker to identify the allocation "camera / gantry".
NOTE:
The brightness balancing of the camera is carried out via the "PC camera board, modular". There-
fore the PCB camera Multicolor and the pertinent "PC camera board, modular" form a mutually
coordinated unit. The parts for cameras and boards are therefore not to be interchanged and - if
faulty - are only to replaced together.
User Manual SIPLACE S-25 HM / HS-50 2 PCB Camera Multicolor (Option)
Software Version SC.502.xx 11/00 Issue 2.3 Focus Heigth: Install/Remove the Distance Plate
35
PPZLWKRXW
GLVWDQFHSODWH
%27720( '*(
VSDFHU
+6
FDPHUDKROGHU
%27720('*(
FDPHUD
PPZLWKRXW
GLVWDQFHSODWHVSDFHU
%27720('*(FDPHUDKROGHU
6+0
%2772 0('*(FDPHUD
2 PCB Camera Multicolor (Option) User Manual SIPLACE S-25 HM / HS-50
2.3 Focus Heigth: Install/Remove the Distance Plate Software Version SC.502.xx 11/00 Issue
36
5HTXLUHG7RROVDQG0DWHULDOV
– Allen wrench, size 2.5
– Oblique-nosed cutting pliers
– Small mirror to be used as an aid while installing/removing the PCB camera Multicolor
– Cable tie L x W = 140 x 3.6 mm Item no.: 00805141-01 3 units / head
– If necessary: Cable clamp, size 6 Item no.: 00805503
(for Placement head S-25 HM)
2