00197569-01_MM_DLM34_Kunde_en - 第5页
Introduction 1.1.1 Conventions for the use of safety instructions Safety Instructions Maintenance Manual SIPLACE Placement Heads DL M3/DLM4 5 1 1 I n t r o d u c t io n Introduction This manual describes maintena nc e ta…
Table of contents
4 Maintenance Manual SIPLACE Placement Heads DLM3/DLM4
4.1.4 Performing Maintenance Tasks 39
4.1.4.1 Cleaning the Turning Station Read Unit 39
4.1.4.2 Z Axis 40
4.1.4.3 Star 41
4.1.4.4 Distributor (back part of head) 41
4.1.4.5 Star brake 43
4.1.4.6 Valve adjustment drives 43
4.1.4.7 Turning station 44
4.1.4.8 Vacuum Generator 45
4.1.4.9 Component sensor (only DLM3) 47
4.1.5 Final Work 48
Introduction
1.1.1 Conventions for the use of safety instructions Safety Instructions
Maintenance Manual SIPLACE Placement Heads DLM3/DLM4 5
1
1 Introduction
Introduction
This manual describes maintenance tasks for all current SIPLACE® placement heads of type DLM.
1.1
1.1 Safety Instructions
Safety Instructions
Nonobservance of these safety instructions may cause injury to personnel and damage to the machine
1.1.1
1.1.1 Conventions for the use of safety instructions
Conventions for the use of safety instructions
This manual contains notes that must be observed to guarantee your personal safety and to avoid dam
-
age to equipment. These notes are highlighted by warning triangles and are indicated as follows accord
-
ing to the level of risk:
DANGER
Nonobservance of these safety instructions may cause injury to personnel and damage to the
machine!
► Please observe the safety instructions in the user manual of the relevant machine for all
work!
DANGER
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable dam
-
age to property will occur if this hazard warning is not observed.
WARNING
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable dam
-
age to equipment may occur if these warning instructions are not followed.
CAUTION
Definition
For the purposes of this manual, this indicates that minor injuries or damage to property may
occur if this caution is not observed.
NOTICE
Definition
For the purposes of this manual, this note provides information about the product or indicates
a part of the manual that requires particular attention.
Introduction
Safety Instructions 1.1.2 Safety Instructions for Maintenance Tasks
6 Maintenance Manual SIPLACE Placement Heads DLM3/DLM4
1.1.2
1.1.2 Safety Instructions for Maintenance Tasks
Safety Instructions for Maintenance Tasks
Danger of burning
Ethanol
SIPLACE cleaning tissue
Consumables
Cleaning and lubri cation
1.1.3
1.1.3 Safety Instructions on Hazardous Materials
Safety Instructions on Hazardous Materials
WARNING
Danger of burning
► Never use inflammable fluids (e.g. alcohol) for cleaning purposes when working in the vi
-
cinity of a naked flame or fire.
► Never spray lubricants or cleaning agents from aerosol cans in the vicinity of a naked flame
or fire.
CAUTION
Ethanol
► Always wear safety goggles and gloves when using concentrated ethanol to clean modules.
► If ethanol should accidentally get into your eyes, rinse your eyes immediately with water.
CAUTION!
SIPLACE cleaning tissue
Harmful: may cause lung damage if swallowed.
Do not inhale vapor / aerosol.
Avoid contact with the skin. If swallowed, do not induce
vomiting. See medical attention immediately and show
the packaging or label.
Wear latex gloves while using the cleaning tissue.
CAUTION
Consumables
Observe the safety data sheets for consumable materials!
CAUTION
Cleaning and lubrication
► Always use ethanol for cleaning – do not use solvents.
► Isopropanol – IPA can be used as an alternative.
► NEVER use compressed air to clean units inside the placement machine or modules.
CAUTION
Observe the safety data sheets
Observe the applicable safety data sheet, when handling hazardous materials (e. g. Loctite
241, ethanol).