YesAX V3.1.2 - Software User Manual - 第19页
Safety 2-1 2 - Safety 2.1 Overview This section prov ides basic safety inform ation necessar y for operating Nordson YESTECH ™ X2 / X3 AXI System s. This section covers the f ollowing topic s: Facility Requirem ent s …
1-6 Introduction
Safety 2-1
2 - Safety
2.1 Overview
This section provides basic safety information necessary for operating Nordson YESTECH™ X2 / X3
AXI Systems. This section covers the following topics:
Facility Requirements
Disposal
Intended Use
Decommissioning Procedures
Safety Warning Labels
Emergency Shutdown
Basic Safety Precautions
Service Shutdown
Lifting and Transport Precautions
Light Tower Status Lights
Electrical Hazards
To further optimize safe X2 / X3 AXI System operation, precautions and recommended practices are
included with the procedures throughout this manual.
WARNING! CAUTION!
Unsafe equipment conditions can result in personal injury or property damage.
Failure to properly operate and maintain the system in accordance with this manual
could cause the built-in safety features to be ineffective.
NOTE Safety is considered a joint responsibility between the original equipment manufacturer
(Nordson YESTECH) and the end-user (owner). All safety precautions and practices
should be in accordance with local regulations and facility policy.
2.2 Facility Requirements
To ensure optimal performance and safety, it is necessary to install the Inline X-ray system in a facility
that meets the necessary requirements. See 29.2 Facility Requirements for detailed information. If you
have any questions, please contact Nordson YESTECH Technical Support.
2.3 Intended Use
Use of Nordson YESTECH equipment in ways other than those described in the documentation supplied
with the equipment may result in injury to persons or damage to property. Some examples of unintended
use of equipment include:
Using the system to x-ray living
organisms
Making unauthorized modifications
Removing or bypassing safety guards or
interlocks
Using incompatible or damaged parts
Using unapproved auxiliary equipment
2-2 Safety
Operating equipment in excess of
maximum ratings
2.4 Safety Warning Labels
Safety labels on the AXI system systems point out potentially hazardous areas and remind personnel to
take necessary safety precautions. Table 2-1 describes safety warning labels that may be on the AXI
systems.
WARNING! CAUTION!
Comply with all safety warning labels or serious injury to personnel or damage to
the AXI system may occur. Worn or damaged labels should be replaced with new
labels having the same part number.
Table 2-1 Safety Hazard Labels
Warning Type
Symbol
Part
Number
Hazard
General Hazard
7223284
(1)
This label warns not to remove the cover while the
machine is in operation.
Disconnect and lock out power before servicing.
Moving Parts
Present
11599
(2)
This label warns of moving parts that can cause
serious injury to hands or fingers. Keep hands away
from moving parts.
Disconnect and lock out power before servicing.
Electrical
(Shock Hazard)
70-0116-00
(1)
or
70-0050-00
(2)
This label warns of a high voltage component that
can cause shock, burn, or death. Use extreme
caution when working in or around these areas.
Disconnect and lock out power before servicing.
Laser Hazard
7254753
(1)
This label warns not to stare into the beam. Serious
eye damage and/or blindness may result.
Disconnect and lock out power before servicing.
X-Ray Hazard
7254754
(1)
This label warns of X-Ray radiation. Do not insert any
part of the body when energized.
Disconnect and lock out power before servicing.
Laser Hazard
11312
This label warns not to stare into the beam. Serious
eye damage and/or blindness may result.
Disconnect and lock out power before servicing.
Laser Hazard
11312
This label warns not to stare into the beam. Serious
eye damage and/or blindness may result.
Disconnect and lock out power before servicing.
Notes: (1) Rectangular labels with symbols and text. These labels are placed on machines that are shipped anywhere but the
European community.
(2) Triangular labels with symbols only. These labels are placed on machines that are shipped to the European
community, referred to as “CE labeled” machines.