00191025-01 - 第654页

SIPLACE 80S/F/G User’s Manual 19 Error Message s Edition 12/96 from S oftware Version SR.009.xx 19.1 Error Messages 19 - 67 535 WPC: Feed axis at li mit switch CAUSE ● Feed axi s at the limi t switch ; limit switc h defe…

100%1 / 736
19 Error Messages SIPLACE 80S/F/G User’s Manual
19.1 Error Messages Edition 12/96 from Software Version SR.009.xx
19 - 66
525 WPC: No tray available.
CAUSE
●
Software error
REMEDY
●
Reboot
526 WPC: Sent set-up contains errors.
CAUSE
●
Software error
REMEDY
●
Reboot
527 Feeder rail of bulk case feeder not installed
CAUSE
●
The feeder rail is not installed on the bulk case feeder
REMEDY
●
Install feeder rail on bulk case feeder
528 Undefined error number of component table (Code 45)
529 Undefined error number of component table (Code 46)
530 Undefined error number of component table (Code 47)
531 Undefined error number of component table (Code 48)
532 Undefined error number of component table (Code 49)
533 Data loss in component table (defective battery)
CAUSE
●
Backup battery flat or defective; Controller A18 defective.
REMEDY
●
Replace battery; fit new A18 and Inform SMD Service.
534 WPC: Fault in feed axis (servo or axis card).
CAUSE
●
Axis board of the feed axis defective; servo of the feed axis defective.
REMEDY
●
Fit new axis board or servo board and inform SMD Service.
SIPLACE 80S/F/G User’s Manual 19 Error Messages
Edition 12/96 from Software Version SR.009.xx 19.1 Error Messages
19 - 67
535 WPC: Feed axis at limit switch
CAUSE
●
Feed axis at the limit switch; limit switch defective.
REMEDY
●
Push feed axis away from limit switch; fit new limit switch.
536 WPC: Axis error of feed axis
CAUSE
●
Undefined reference point or type of positioning; undefined axis command; position outside the
travel range.
REMEDY
●
Reboot; inform SMD Service.
537 WPC: Feed axis servo released.
CAUSE
●
Servo disabled at the axis board.
REMEDY
●
Switch servo back on at the axis board.
538 WPC: Error in jaw position
CAUSE
●
At the zero point position the reference Bero of the feed axis is not actuated; incorrect zero point cor-
rection; Bero defective.
REMEDY
●
Correct zero point correction; replace Bero.
539 WPC: Fault in lifting axis (servo or axis card)
CAUSE
●
Axis board of the lifting axis defective; Servo of the lifting axis defective.
REMEDY
●
Fit new axis board or servo board and inform SMD Service.
540 WPC: Lifting axis at limit switch
CAUSE
●
Lifting axis at the limit switch; limit switch defective.
REMEDY
●
Release the brake of the lifting axis and push lifting axis away from limit switch; fit new limit switch.
19 Error Messages SIPLACE 80S/F/G User’s Manual
19.1 Error Messages Edition 12/96 from Software Version SR.009.xx
19 - 68
541 WPC: Axis error of lifting axis
CAUSE
●
Undefined reference point or type of positioning; undefined axis command; position outside the
travel range.
REMEDY
●
Reboot; inform SMD Service.
542 WPC: Lifting axis servo released
CAUSE
●
Servo disabled at the axis board.
REMEDY
●
Switch servo back on at the axis board.
543 WPC: Control switched off.
CAUSE
●
Control of the component carriage failed; plugged connection faulty.
REMEDY
●
Check plugged connection and inform SMD Service.
544 WPC: Protection at component table open.
CAUSE
●
Guard at the component carriage opened; protective switch or cable connection defective.
REMEDY
●
Close guard; fit new protective switch and check cable connection.
545 WPC: Error while transporting tray
CAUSE
●
When a tray is being supplied the "Tray ready" Bero is covered; the "Tray ready" Bero is defective;
when a tray is being returned the "Tray in magazine" Bero is covered; the "Tray in magazine" Bero is
defective.
REMEDY
●
Check the "Tray ready" Bero and "Tray in magazine" Bero.
546 WPC: Error in saved set-up.
CAUSE
●
At pick-up of the component division number not in the set-up; checksum of the set-up erroneous.
REMEDY
●
Reboot and inform SMD Service.