00191025-01 - 第696页

SIPLACE 80S/F/G User’s Manual 19 Error Message s Edition 12/96 from S oftware Version SR.009.xx 19.1 Error Messages 19 - 1 09 1017 z axis; GU3: Position outside of tr avel range CAUSE ● Not used REMEDY ● 1018 xk axis: Ta…

100%1 / 736
19 Error Messages SIPLACE 80S/F/G User’s Manual
19.1 Error Messages Edition 12/96 from Software Version SR.009.xx
19 - 108
1010 Glue: z axis; GU1: cannot be moved any further upwards
CAUSE
●
When the start button is pressed the z12 axis is below the minimum position
REMEDY
●
The servo-amplifier should be checked; slide the z1 axis upwards by hand
1011 Glue: z axis; GU2: cannot be moved any further upwards
CAUSE
●
When the start button is pressed the z2 axis is below the minimum position
REMEDY
●
The servo-amplifier should be checked; slide the z2 axis upwards by hand
1012 Glue: z axis; GU3: cannot be moved any further upwards
CAUSE
●
When the start button is pressed the z3 axis is below the minimum position
REMEDY
●
The servo-amplifier should be checked; slide the z3 axis upwards by hand
1013 xk axis: Position outside of travel range
CAUSE
●
Not used
REMEDY
●
1014 yk axis: Position outside of travel range
CAUSE
●
Not used
REMEDY
●
1015 z axis; GU1: Position outside of travel range
CAUSE
●
Not used
REMEDY
●
1016 z axis; GU2: Position outside of travel range
CAUSE
●
Not used
REMEDY
●
SIPLACE 80S/F/G User’s Manual 19 Error Messages
Edition 12/96 from Software Version SR.009.xx 19.1 Error Messages
19 - 109
1017 z axis; GU3: Position outside of travel range
CAUSE
●
Not used
REMEDY
●
1018 xk axis: Target position not reached
CAUSE
●
Machine data not correct; mechanism is jamming;
drive motor, tachometer, incremental encoder, servo-amplifier defective; calibration of the axis incor-
rect.
REMEDY
●
Check machine data; check the mechanism; check the axis calibration
or check the components; if necessary, replace
1019 yk axis: Target position not reached
CAUSE
●
Machine data not correct; mechanism is jamming;
drive motor, tachometer, incremental encoder, servo-amplifier defective; calibration of the axis incor-
rect.
REMEDY
●
Check machine data; check the mechanism; check the axis calibration
or check the components; if necessary, replace
1020 z axis; GU1: Target position not reached
CAUSE
●
Machine data not correct; mechanism is jamming;
drive motor, tachometer, incremental encoder, servo-amplifier defective; calibration of the axis incor-
rect. Cam is in incorrect position with respect to zero pulse
REMEDY
●
Check machine data; check the mechanism; check the axis calibration
or check the components; if necessary, replace, fit cam in correct rotational position; redetermine
zero point correction
1021 z axis; GU2: Target position not reached
CAUSE
●
Machine data not correct; mechanism is jamming;
drive motor, tachometer, incremental encoder, servo-amplifier defective; calibration of the axis incor-
rect.
Cam is in incorrect position with respect to zero pulse
REMEDY
●
Check machine data; check the mechanism; check the axis calibration
or check the components; if necessary, replace, fit cam in correct rotational position; redetermine
zero point correction
19 Error Messages SIPLACE 80S/F/G User’s Manual
19.1 Error Messages Edition 12/96 from Software Version SR.009.xx
19 - 110
1022 z axis; GU3: Target position not reached
CAUSE
●
Machine data not correct; mechanism is jamming;
drive motor, tachometer, incremental encoder, servo-amplifier defective; calibration of the axis incor-
rect.
Cam is in incorrect position with respect to zero pulse
REMEDY
●
Check machine data; check the mechanism; check the axis calibration
or check the components; if necessary, replace, fit cam in correct rotational position; redetermine
zero point correction
1023 xk axis: deactivated
CAUSE
●
Axis has been deactivated at the axis board (servo)
REMEDY
●
Switch on the axis at the axis card
1024 yk axis: deactivated
CAUSE
●
Axis has been deactivated at the axis board (servo)
REMEDY
●
Switch on the axis at the axis card
1025 z axis; GU1: deactivated
CAUSE
●
Axis has been deactivated at the axis board (servo)
REMEDY
●
Switch on the axis at the axis card
1026 z axis; GU2: deactivated
CAUSE
●
Axis has been deactivated at the axis board (servo)
REMEDY
●
Switch on the axis at the axis card
1027 z axis; GU3: deactivated
CAUSE
●
Axis has been deactivated at the axis board (servo)
REMEDY
●
Switch on the axis at the axis card