00191025-01 - 第91页

SIPLACE 80S/F/G User’s Manual 5 Placement Edition 12/96 from S oftware Version SR.009.xx 5.4 Com ponent Handling 5 - 15 Fig. 5.4.3 ● Acknow ledge the w arning mes sage by pre ssing the spaceb ar . ● Check your inputs and…

5 Placement SIPLACE 80S/F/G User’s Manual

5.4 Component Handling Edition 12/96 from Software Version SR.009.xx

5 - 14

Input Options

Lefthand window:

Track barcode:

Input of the track bar-code using the bar-code pen by running it over the

track bar-code at the machine or by using the keyboard to enter the track bar-code.

Des'd BC w. filt:

Possible bar-codes are shown here.

If a filter was entered in the LC for certain positions in the barcode this will be

shown here. The masked-out positions are marked by a rectangle.

Comp. barcode:

Input of component barcode by reading in the barcode on the component package

or by entering the component barcode via keyboard.

Righthand window:

Displays the table side, track number and component name belonging to the track barcode selected.

Listing the empty tracks when the "Refill" menu is called during placement. In this listing it is possible to

display, by pressing the

spacebar

, the track barcode belonging to the line which was selected with the

cur-

sor bar

When the refill check is not enabled (see Chapter 5.3 "Options") it is possible to call the corresponding

component barcode by pressing the spacebar once more.

BC:

* With this track at least one component bar-code will be present. Bar-code comparison is possible.

When fill check is enabled the bar-code comparison is mandatory.

- This component bar-code is not found. You can fill manually.

NOTE

Up to 40 characters may be entered as a component barcode. The display can be scrolled in the display area

Component barcode with filter. Arrows indicate in which direction the characters in the display area should be

read.

5.4.4.1 Setting Tracks Full

●

Read in or enter the track bar-code and then the component bar-code of the track to be dealt with.

●

Press the

Return key

or move the

pen reader

over the return barcode. If the track and the component bar-

code agree with one another, the corresponding line in the righthand window is highlighted by a yellow

background. If the track and component barcodes do not agree with one another, a warning message is

displayed.

SIPLACE 80S/F/G User’s Manual 5 Placement

Edition 12/96 from Software Version SR.009.xx 5.4 Component Handling

5 - 15

Fig. 5.4.3

●

Acknowledge the warning message by pressing the

spacebar

●

Check your inputs and whether you have entered the right component. Repeat the procedure.

●

If the corresponding line in the righthand field has a yellow background, press the

Return key

This line is deleted from the righthand window and this track reported to the machine as full and ready for

placement.

5.4.4.2 Refilling Tracks Which Have Not Yet Been Emptied

If tapes are spliced onto tracks which have not yet been emptied, or they are refilled with components, then

proceed as follows to check whether the track corresponds to the component which has been supplied:

●

Select the "Refill" menu.

●

For the track affected, follow the procedure described in Section 5.4.4.1 (Setting tracks full).

Error

State

Action

Fill empty tracks separately and continue

2007

TRX-7

Y-7

TRY-3

ESC: abort Ret. input Blank: select Tab: change wind

1. BC + filter:

4. BC + filter:

2. BC + filter:

3. BC + filter:

5. BC + filter:

6. BC + filter:

Track barcode:

Comp barcode:

12 1 0

CO-R12534 *

33 1 0

CO-R12534 -

48 1 0

CO-R12534 -

Refill

Level Comp nameDivTrackLoc

WARNING

Track and comp. barcode do not match

Press space bar

5 Placement SIPLACE 80S/F/G User’s Manual

5.4 Component Handling Edition 12/96 from Software Version SR.009.xx

5 - 16

5.4.4.3 Setting Empty Tracks Full

If one or more tracks has or have been completely emptied and appear as an error message on the screen,

then proceed using one of the two alternatives given below:

With refill check

●

Select the "Refill" menu. All empty tracks are listed there automatically in the righthand window.

●

Using the

Tab key

activate the cursor bar in the righthand window.

●

Either position the cursor bar using the

cursor keys

over the track you wish to process and press the

spacebar

or read in the track barcode using the pen reader. The track barcode is now shown in the

lefthand window.

●

Read in or enter one of the possible component bar-codes and then press the

Return key

●

If the corresponding line in the righthand field has a yellow background, press the

Return key

This line is deleted from the screen and this track is reported to the machine as full and ready for

placement.

NOTE

If "No component barcode (- in column BC)" has been entered for the selected track, you may proceed as

with "without refill check".

Without refill check

●

Select the "Refill menu". All empty tracks are listed there automatically in the righthand window.

●

Using the

Tab key

activate the cursor bar in the righthand window.

●

Either position the cursor bar using the

cursor keys

over the track you wish to process and press the

spacebar

or read in the track barcode using the pen reader. The track barcode is now displayed in the

lefthand window.

●

Press the

spacebar

again. In the lefthand window the first of the corresponding component bar codes will

now be displayed.

●

Press the

Return key

. This line is deleted from the screen and this track reported to the machine as full and

ready for placement.

NOTE

All empty tracks can also be set simultaneously to full after entering the line engineer password with the

menu item "Set tracks full" (see Section 5.4.3). The refill check also must be disabled.