KD-2077_使用说明书 - 第6页
iv 为了安全使用 KD-2077 的注意事项 1. 为了防止触电引起的事故，请勿在接通电源的状态下打开电气设备箱。 2. 为防止触电，请勿在拆下接地线的状态下运行。 1. 为防止人身受伤，请勿在拆下安全罩、安全装置等状态下运行。 2. 为防止人身受伤，请务必小心，以免头发、衣服等被卷入传送带链。此外， 请勿戴手套。 3. 为防止人身受伤，维护时（加油、调试、日常检修），请切断电源。 4. 为防止人身受伤，请在电源线上使用漏电断路器。 …
iii
注意（续）
各使用环节中的注意事项
搬 运
1. 为防止提起、移动时发生颠倒、掉落事故，请采取充分的安全对策。
2. 请在下述环境下运输及保管
环境条件 温度 ：-15℃～70℃
湿度 ：20％～95％RH (但不得有露水)
开 封
1. 请阅读装运用集装箱内所述的所有指示。
2. 包装带绝不能用刀割开。
3. 请保管好装运用的器材。
安 装
1. 为避免正在运行的机器意外移动引起事故，请用高度调节装置，将滚动轮悬起。
2. 请将本机器设置在水平的地方。
3. 为防止触电、漏电、火灾，电缆类请使用附件，并连接在规定的位置。
4. 为防止触电、漏电、火灾，在运行时，电缆请勿过度加压。
5. 电源插头、I/F 电缆的连接器，请固定到位。在拔出电源插头、I/F 电缆时，要握住连接器部拔出。
运行前
1. 为了防止人身事故，在接通电源前，请确认连接器、电缆类无损伤、脱落、松弛等。
2.
为了防止人身事故，请勿将手放入驱动部。
加 油
1. 黄油请使用 JUKI 指定的黄油。
2. 为了防止炎症、斑疹，黄油附着在眼睛里或身体上时，请立即进行清洗。
3. 误食时，为防止腹泻、呕吐，请立即请医生诊断。
维 护
1. 为了防止因操作不熟悉而引起的事故，修理、调试作业应由熟悉机械的保全技术员进行。更换零部件
时，请使用本公司的纯正部件。对使用非纯正部件所引起的事故，本公司概不负责。
2. 为了防止操作不熟练而引起的事故和触电事故，有关电气的修理、保全（包括配线），请委托有电气
专业知识的人员或本公司、销售公司的技术人员。
3. 为防止意外起动造成事故，请拆下气源管，放出剩余的空气后再进行维护。
4. 为防止人身事故，进行修理调试、零部件更换等作业后，请确认螺钉、螺母等稳固不松弛。
使用环境
1. 为防止因错误操作而引起的事故，请勿在受高频焊机等噪声源（电磁波）影响的环境下使用。
2. 为防止因错误操作而引起的事故，请勿在电源电压超过额定电压±10％的情况下使用。
3. 为防止因错误操作而引起的事故，请在 0.5±0.05Mpa 的供气压力下使用。
4. 为了安全使用，请在下述环境下使用。
运行的环境条件 温度 ：10℃～35℃
湿度 ：30％～80％RH (但不得有露水)
标高 ：1,000m 以下
5. 为防止电气部件破损引起的事故，从冷处将机器突然移动到暖处时，有时会结露，因此，请在完全无
需担心水滴后再接通电源。
6. 为防止电气部件破损而引起的事故，打雷时，请停止使用，并拔出电源插头。
注意
iv
为了安全使用 KD-2077 的注意事项
1.为了防止触电引起的事故，请勿在接通电源的状态下打开电气设备箱。
2.为防止触电，请勿在拆下接地线的状态下运行。
1.为防止人身受伤，请勿在拆下安全罩、安全装置等状态下运行。
2.为防止人身受伤，请务必小心，以免头发、衣服等被卷入传送带链。此外，请勿戴手套。
3.为防止人身受伤，维护时（加油、调试、日常检修），请切断电源。
4.为防止人身受伤，请在电源线上使用漏电断路器。
1.本装置的操作系统采用 Windows XP（包括以太网通信功能）。
除安装本装置提供的软件之外，加装其他软件，不保证正常运行。对 SSD 内组装的文件
进行转移、重命名、文件夹·文件的压缩、复制，也同样不保证正常运行，敬请谅解。
● 万一出现此钟情况，需要更换新的 SSD，有可能丢失数据，务请格外注意。
为保护操作系统，使用了 Enhanced Write Filter(EWF)组件，进行了 C 盘 ROM 化。
1.请不要在 C 盘保存文件。
把文件保存在 ROM 化后的 C 盘，会仿真占用主存储器。因而，把文件存在 C 盘里时，会
增加主存储器的使用量，压迫系统。反复保存后可能造成内存不足，显示系统错误，可
能需要重启本设备。
2.需要修改 OS 信息时，必须刷新 C 盘操作。操作方法请参见使用说明书「1－6 更新 C 盘的
操作」。
需要修改 OS 信息的操作是指下列事项：
·KD-2077 系统软件、Flex Line DB 的版本升级
·触摸屏自我校正
·添加打印机
·设置网络（IP 地址、工作组等）
·添加用户
·变更资源管理器的设置
·变更 UPS 实用程序（UPSilon2000）的设置
●要变更操作系统信息时，在修改 C 盘操作后，需要重启一次本装置。
1.本装置配备有 UPS（可选项），以保护停电时的生产程序等。
为防止 UPS 内置电池劣化，请勿在非通电状态下将本装置放置 6 个月以上。
●本装置以电流总断路器及总开关 ON 的状态为通电状态。
〈安全盖〉
1．开关安全盖时请注意下列事项。
• 打开安全盖时要把盖子向上开足直到上了锁，确认上了锁后再放开手。
没有上好锁就放开手时，盖子有落下来的危险。
• 关盖子时先解开锁，再关闭盖子。
（请注意，解开锁时不要使盖子落下来导致受伤。）
• 不要过渡增加盖子、手把等的负荷。
1. 安装等时请不要站到机器上面，以免损坏外罩类。
1. 操作机器时，请注意以下事项。否则不能正确运行。
・不要使用任务管理器，强制结束操作。
・在机器工作中，请不要按下×按钮。
注意
危险
注意
注意
注意
注意
注意
注意
・为了确保安全使用本点胶机，作以下说明。
目 录
第 1 部 基本篇
第 1 章 设备概要
1-1 本设备的概要 ···································································································· 1-1
1-1-1 前言 ········································································································ 1-1
1-1-2 特长 ········································································································ 1-2
1-1-3 系统构成 ·································································································· 1-3
1-2 本设备的构成 ···································································································· 1-4
1-2-1 本设备的构成 ······························································································ 1-5
1
-2-1-1 基板传送部分的构造 ········································································ 1-6
1
-2-1-2 点胶头单元的构成 ··········································································· 1-7
1-2-1-3 针 ································································································ 1-8
1
-2-1-4 OCC 的构成 ················································································· 1-10
1-2-2 设备规格 ································································································ 1-11
1-2-3 电气规格 ································································································ 1-13
1-2-4 对象胶粘剂及注射器 ················································································· 1-14
1-2-5 对象元件 ································································································ 1-14
1-2-6 印刷基板规格 ·························································································· 1-15
1-2-7 水头差补正功能、残量检知功能 ·································································· 1-18
1-2-8 X,Y,Z,θ
轴的说明 ·····················································································
1-19
1-2-9 与外部设备的接口 ···················································································· 1-20
1-2-10 略语说明 ······························································································ 1-23
1-3 基本操作 ········································································································ 1-24
1-3-1 画面的构成 ····························································································· 1-24
1-3-2 输入装置 ································································································ 1-26
1-3-3 操作方法 ································································································ 1-34
1-4 菜单与命令 ····································································································· 1-42
1-5 文件 ·············································································································· 1-53
1-5-1 新建······································································································ 1-54
1-5-2 打开（文件的读入） ················································································· 1-53
1-5-3 保存······································································································ 1-54
1-5-4 另存为 ··································································································· 1-54
1-5-5 文件管理 ································································································ 1-56
1-5-6 生产程序初始目录 ···················································································· 1-57
1-5-7 打印机设置 ····························································································· 1-57
1-5-8 打印······································································································ 1-58
1-5-9 设备信息的保存 ······················································································· 1-60
1-5-10 保存图
像数据 ························································································ 1-64
1-5-11 硬件安全拆卸 ························································································ 1-68
1-6 C 盘的更新操作 ······························································································· 1-69
第 2 章 生产程序
2-1 流程图 ············································································································· 2-1
2-2 概要 ················································································································ 2-2
2-2-1 生产模式 ·································································································· 2-2
2-2-2 生产流程 ·································································································· 2-3
2-2-3 生产主菜单的构成 ······················································································ 2-4