00198142-01_AI_Stationary-Camera-25-33_TX_de_en - 第60页
Introduction Staff Qualifications and Training 1.3.4 Validity of Document 60 Stationary Camera Type 25/33 Stationäre Kamera Typ 25/ 33 1.3.3.5 1 . 3 . 3 . 5 D is p a t c h in g E S D M o d u le s Dispatching ESD Modules …
Introduction
1.3.3 ESD Guidelines Other Instructions
Stationary Camera Type 25/33 Stationäre Kamera Typ 25/33 59
1.3.3
1.3.3 ESD Guidelines
ESD Guidelines
1.3.3.1
1.3.3.1 Definition of ESD
Definition of ESD
1.3.3.2
1.3.3.2 Important Measures to Protect Against Static Charging
Important Measures to Protect Against Static Charging
► Most plastics can easily become charged and must therefore be kept away from at-risk components.
► Always ensure that people, the workplace and packaging are safely earthed when handling electro
-
static sensitive components.
1.3.3.3
1.3.3.3 Handling ESD Modules
Handling ESD Modules
Do not touch electronic modules unless it is absolutely essential to do so in order to carry out other work.
If it is necessary, make sure that you do not touch the pins or printed conductors when you pick up flat
modules.
Do not touch components unless
▪ You are constantly earthed by an ESD wrist strap or
▪ You are wearing ESD shoes or ESD shoe earthing strips on an ESD floor.
Always discharge yourself before you touch an electronic module. To do this, simply touch a conductive
and earthed object immediately before you touch the module (such as unpainted parts of a switch cab
-
inet, a water pipe, etc.).
Do not allow modules with chargeable and highly insulating materials to touch one another, e.g. plastic
films, insulating table surfaces or items of clothing made from synthetic fibers.
Always place the modules on a conductive surface (table with an ESD coating, conductive ESD foam,
ESD bag or container).
Do not bring modules near visual display units, monitors or televisions. Keep them at least 10 cm away
from the screen.
1.3.3.4
1.3.3.4 Measurements and Modifications to ESD Modules
Measurements and Modifications to ESD Modules
Measurements of the assemblies may only be taken if
▪ The measuring device has been grounded (e.g. via protective conductor) or
▪ The measuring head of the potential-free measuring device has been briefly discharged before
measurement (e.g. touching blank metal control unit housing).
► Always use an earthed soldering iron if you carry out any soldering work.
Almost all of the modules in use today are equipped with highly integrated MOS blocks and compo
-
nents. The manufacturing techniques used mean that these electronic components are extremely sen
-
sitive to overvoltage and thus to electrostatic discharge.
ESD label
The abbreviation for such modules is "ESD"(Electrostatic Sensitive Device). This is
used internationally, although the German abbreviation "EGB" may also be seen. The
following symbol on cabinet rating plates, racks or packaging indicates that compo
-
nents which are sensitive to electrostatic discharge have been used and thus that the
modules concerned are also touch-sensitive.
ESDs can be destroyed by voltages and power levels that are far below the level that can be perceived
by humans. Such voltages occur if a person touches a component or module without earthing them
-
selves. Components that are exposed to such overvoltages do not generally appear to be defective im
-
mediately - incorrect behavior starts after the component or module has been in operation for some
time.
Introduction
Staff Qualifications and Training 1.3.4 Validity of Document
60 Stationary Camera Type 25/33 Stationäre Kamera Typ 25/33
1.3.3.5
1.3.3.5 Dispatching ESD Modules
Dispatching ESD Modules
► Always store modules and components in conductive packaging (e.g. metallized plastic bags or met
-
al sleeves) and dispatch them in conductive packaging.
► If the packaging is not conductive, place the modules in a conductive envelope before packaging.
Use conductive foam rubber, ESD bags, domestic aluminum foil or paper, for example. NEVER use
plastic bags or film.
► If the module has integral batteries, ensure that the conductive packaging does not touch or short-
circuit the battery terminals and, if necessary, first cover the terminals with insulating tape or mate
-
rial.
1.3.4
1.3.4 Validity of Document
Validity of Document
TX
This document is valid for all SIPLACE TX machines.
The work described in this manual is divided into modules and is largely identical for all machine types:
▪ If the work required for specific machines should differ from the standard procedure, this will be in
-
dicated with reference to the machine number, series and delivery state.
▪ Diagrams should be seen as examples e.g. the diagram of a specific machine type or a machine with
different paint finish does not mean that the following information only applies to the machine type
shown.
Please read the circuit diagram folder for any electrical checks.
1.3.5
1.3.5 Release History
Release History
1.4
1.4 Staff Qualifications and Training
Staff Qualifications and Training
Qualified or adequately trained personnel means that these people are familiar with the setting up, op
-
eration and maintenance of automatic placement systems and add-on devices and are suitably qualified,
e.g.:
▪ Have been trained, instructed or authorized to switch on and off, isolate, earth and identify electrical
circuits and system components in accordance with normal safety standards.
▪ Have been trained or instructed in the upkeep and use of appropriate safety equipment in accord
-
ance with normal safety standards.
▪ Have received first aid training.
Document
SIPLACE TX Series
Stationary camera type 25/33
Assembly Instructions
Edition Changes
02/2016 First edition
Brief description
Product Description
Stationary Camera Type 25/33 Stationäre Kamera Typ 25/33 61
2
2 Brief description
Brief description
2.1
2.1 Product Description
Product Description
SIPLACE TX1 and TX2 machines can accommodate an FC camera type 25 or an IC camera type 33 in
location 1.
NOTE: The upper section of the camera is assigned specifically to the lower section of the camera!
1. FC camera type 25 in the machine
1. IC camera type 33 in the machine
NOTICE
The upper section of the camera is assigned specifically to the lower section of the camera!
The upper section of the camera may not be used with a different bottom section. Both the up
-
per and lower sections are mechanically and electrically coordinated and may not be ex
-
changed for use with other cameras. The serial and version numbers of the top and bottom
sections of the camera must be identical.