Error Code List.pdf - 第58页
RL1 31 ERROR CODE LIST 2.4 Errors DA8EEC- 91-210- A0 2.4- 35 2658 Le ft ra il c ove r sa fe ty de te ct ion DESCRI PTIO N The m ach ine be ca m e a sa fe ty s top co ndi tion by the sa fe ty de tec tio n in the le ft rai…
RL131
ERROR CODE LIST
2.4 Errors
DA8EEC-91-210-A0
2.4-34
2649
Carry miss
DESCRIPTION
PCB loading or unloading failure was detected.
CAUSE
Pin of the PCB transfer arm may not have been positioned properly.
Rail width may be not wide enough to feed PCB smoothly.
Orientation of PCB may be incorrect.
SOLUTION
Check the transfer arm for proper condition.
Check for correct PCB rail width.
Check the PCB for proper condition.
NOTE
2652
Rear left safety detection
DESCRIPTION
The machine became a safety stop condition by the safety detection in the left feeder cover.
CAUSE
The cover of the left feeder has been opened.
SOLUTION
Press [Return] button after closing the cover. Then please release the safety stop condition to push [[Start]] with
[[ENABLING]].
NOTE
2653
Rear right safety detection
DESCRIPTION
The machine became a safety stop condition by the safety detection in the right feeder cover.
CAUSE
The cover of the right feeder has been opened.
SOLUTION
Press [Return] button after closing the cover. Then please release the safety stop condition to push [[Start]] with
[[ENABLING]].
NOTE
2656
Front cover safety detection
DESCRIPTION
The machine became a safety stop condition by the safety detection in the front cover.
CAUSE
The cover of the front has been opened.
SOLUTION
Press [Return] button after closing the cover. Then please release the safety stop condition to push [[Start]] with
[[ENABLING]].
NOTE
2657
Right rail cover safety detection
DESCRIPTION
The machine became a safety stop condition by the safety detection in the right rail cover.
CAUSE
The cover of the right rail has been opened.
SOLUTION
Press [Return] button after closing the cover. Then please release the safety stop condition to push [[Start]] with
[[ENABLING]].
NOTE
RL131
ERROR CODE LIST
2.4 Errors
DA8EEC-91-210-A0
2.4-35
2658
Left rail cover safety detection
DESCRIPTION
The machine became a safety stop condition by the safety detection in the left rail cover.
CAUSE
The cover of the left rail has been opened.
SOLUTION
Press [Return] button after closing the cover. Then please release the safety stop condition to push [[Start]] with
[[ENABLING]].
NOTE
2663
Cancel replacement completion input (open rear left cover)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Rear left cover was opened.
SOLUTION
Please close the rear left cover then input part replacement completion switch again.
NOTE
2664
Cancel replacement completion input (open rear right cover)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Rear right cover was opened.
SOLUTION
Please close the rear right cover then input part replacement completion switch again.
NOTE
2665
Cancel replacement completion input (float left feeder)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Feeder in the left part supply floats.
SOLUTION
Please confirm feeder condition then input part replacement completion switch again.
NOTE
2666
Cancel replacement completion input (float right feeder)
DESCRIPTION
Part replacement completion input was canceled.
CAUSE
Feeder in the right part supply floats.
SOLUTION
Please confirm feeder condition then input part replacement completion switch again.
NOTE
RL131
ERROR CODE LIST
2.4 Errors
DA8EEC-91-210-A0
2.4-36
2670
Insertion error (Neither lead detection)
DESCRIPTION
Component failed to be inserted in the target hole on the PCB (or failed to be clinched properly).
CAUSE
(1) Bent component leads.
(2) Worn pusher rubber.
(3) Worn V-cutter blade.
(4) Improperly adjusted V-cutter position.
(5) Error detected although the component was inserted properly.
(6) Worn pallet rubber.
(7) Mismatched insertion hole position and so on.
ACTION
(1) Take care not to bend leads when replacing components.
(2) Replace the pusher rubber with a new one.
(3) Replace the V-cutter blade with a new one.
(4) Check the shape of the cut leads and adjust the V-cut position.
(5) Decrease the “INS LEVEL” value in the parts data.
(6) Replace the pallet rubber with a new one.
(7) Perform hole position teaching.
SOLUTION
Take the above actions appropriately.
Close the error screen and remove the component concerned.
Refer to the pop-up guidance for the method of resuming or restarting production.
NOTE
2673
Anvil short error (left & right lead detection)
DESCRIPTION
Insertion of both leads was detected during trial where no part is supposed to be inserted.
CAUSE
Improper adjustment of clincher blade position
Dirt adhered to the inside of the clincher.
Clogged suction hose of the anvil
Contact failure in the wiring to the insertion detection box
Anvil is within the dead space at the insertion position.
Another part inserted to a position where a part has already been inserted.
SOLUTION
Readjust the clincher.
Remove the clincher and clinch base, then clean inside.
Clear the clogged hose. Dispose of any accumulated wastes inside the waste bottle.
Check for wire break and contact of the connectors.
Check the dead space.
Check the insertion position.
NOTE
2674
Anvil short error (left lead detection)
DESCRIPTION
Insertion of left lead was detected during trial where no part is supposed to be inserted.
CAUSE
Improper adjustment of clincher blade position
Dirt adhered to the inside of the clincher.
Clogged suction hose of the anvil
Contact failure in the wiring to the insertion detection box
Anvil is within the dead space at the insertion position.
Another part inserted to a position where a part has already been inserted.
SOLUTION
Readjust the clincher.
Remove the clincher and clinch base, then clean inside.
Clear the clogged hose. Dispose of any accumulated wastes inside the waste bottle.
Check for wire break and contact of the connectors.
Check the dead space.
Check the insertion position.
NOTE