德森印刷机说明书之使用手册2 - 第33页

德森精密机械设备有限公司 Shenzhen Shenzhen Shenzhen Shenzhen DeSen DeSen DeSen DeSen P re cision P re cision P re cision P re cision Machine Machine Machine Machine Co., Co., Co., Co., Ltd Ltd Ltd Ltd . . . . - 32 - 工作台驱动马达 Motor fo…

德森精密机械设备有限公司

Shenzhen

DeSen

Precision

Machine

Co.,

Ltd

- 31 -

刮刀驱动马达

Squeegee d rive

m otor

调节螺钉

刮刀运动同步带

Synchronous belts of squeegee

m oving

齿形带松紧调节螺钉

Adjusting s crew for c

b elt

Slightly loosen the binder bolts of the backstands for the synchronous belts ;

Adjust the position of the backstands as we need

Press the belts with hand and

will be OK if the belt feels not so tight and not so

loose ( we can also use a frequency recorder to measure the tension of the cog belt

in this way: beat the cog belt quickly and watch the display on the recorder, if

shows between 90Hz ± 5Hz , then

will be OK).

Tighten the binder bolts on the backstands for the synchronous belts.

注意：

Notes:

调整时不能使同步带伸长变形。

Do not stretch the belts when they are adjusted.

Adjustable screw

图 3-3 刮刀驱动皮带调节

Figure 3-3 Belt adjustment of Squeegee Drive

3.3.3

印刷部分： 3.3.3.

3.3.3.

Printing

德森精密机械设备有限公司

Shenzhen

DeSen

Precision

Machine

Co.,

Ltd

- 32 -

工作台驱动马达

Motor for d riving

w orkbench

同步带 synchronous belts

图 3-4 印刷工作台及运输导轨

Figure

3-4

Printing

Workbench

and

Transportation

Guide

rail

注意：

两运输导轨的平行度以及与工作平台的平行度在出厂前已调试好。

Notes:

The parallelism of the both Guide rails and the one between the rails and

workbench have been adjusted well.

印刷工作台：

Workbench

for

Printing:



检查印刷工作台上是否有锡膏残渣；



Check if there are remains of solder paste on the workbench ’



用干净的棉布沾少许酒精做必要的清洁；



Moisten a piece of cotton cloth with alcohol to do some necessary cleaning;



检查传输系统及定位夹紧部位上是否有锡膏残渣；



Check if there are remains of solder paste in the system of transportation as well

as the positions for fixing and clamping;



取下工作台四周盖板，用干净的棉布清洁导向杆及直线导轨；



Take

off the covers of the workbench and clean the steering bar and linear guide

with a piece of clean cotton cloth;



用 NSK 导轨、丝杆专用润滑油润滑导向丝杆及直线导轨；



Lubricate the steering bar and linear rails with NSK special lubricant for guide

rails and bars;



用棉布沾少许酒精清洁传感器；



Moisten the cotton cloth with a little alcohol and use

to clean the sensor;



需要时调整 X 、 Y 运动方向的同步带，调整方法同刮刀同步带；



Adjust the synchronous belts which run in the direction of X, y in the same way as

the adjustment of the belts for the squeegee;



将盖板重新盖好。



Put the covers back.

德森精密机械设备有限公司

Shenzhen

DeSen

Precision

Machine

Co.,

Ltd

- 33 -

同步带松紧调节螺钉

Adjusting s crew for the tension of

synchronous belts

阻挡螺钉 Barrier screw

工作台板面

Board of the workbench

图 3-5 工作台驱动部分

Figure 3-5 Workbench Drive

小心：

Caution:

不要使用有机溶液：氨水、苏打水或苯清洁传感器。

Do not use organic solution like ammonia, soda water or benzene to cleanse the sensor.

工作台升降：

Workbench

Lifting



打开机器下部气动组件柜门及柜箱；



Open the cabinet door of pneumatically elements below the machine;



清洁机器下部工作台升降丝杆和直线导轨；



Cleanse the elevating screw and linear rail on the workbench below the machine;



用 NSK 丝杆、导轨专用润滑油润滑升降丝杆和导轨；



Lubricate the elevating screw and guide rail with NSK special lubricant for screws

and guide rails;



关闭气动组件柜门；



Close the cabinet door of the pneumatically elements;



定期检查工作台顶板阻挡螺钉磨损情况，保证工作台上升接触到阻挡螺钉时，工作

台板面到运输导轨上平面的高度为 110 ± 0.02mm 。



Periodically check the abrasion pattern of the barrier screw on the top board of

the workbench and when the workbench lift to the barrier screw, the height

between board of the workbench and the surface of the transportation guide rail

is 110 ± 0.02mm 。