德森印刷机说明书之使用手册2 - 第37页

德森精密机械设备有限公司

Shenzhen

DeSen

Precision

Machine

Co.,

Ltd

.

- 35 -

运输带松紧调节

Tension Adjustment of Conveyor

Belt

运输导轨

Transportation

Guide Rail

图 3-7 气动组件图 Figure 3-7 P

P

neumatic

Components

3.3.5

传动部分：

3.3.5

Transmission

Part

调整运输传送带的松紧

Adjusting

the

Tension

of

the

Belt

图 3-8 运输皮带张紧

Figure 3-8 T ension of Conveyor Belt



检查两运输导轨上的皮带；



Check the belts on both of the rails;



松开两导轨右端外侧的两个皮带张紧轮调节螺钉；



Loosen the screws on both of the backstands outside on the right of the rails;



向内或向外移动两个张紧轮位置；



Move the backstands inwards or outwards;



用手试压传送带，感觉松紧适宜即可；



Press the belts with hand and

it

will be OK if

it

feels not so tight and not so loose;



拧紧张紧轮调节螺钉。



Tighten the screw of the backstands.

注意：

调整时不能使运输传送带伸长。

德森精密机械设备有限公司

Shenzhen

DeSen

Precision

Machine

Co.,

Ltd

.

- 36 -

Notes

: Do not stretch the belts during adjustment.

3.3.6

Camera

Drive

Y



检查 Camera Drive Y 轴导向丝杆的磨损情况；



Check the abrasion pattern of the Camera Drive Y guide rail;



清洁并润滑导向丝杆；



Clean and lubricate the steering bar ;



检查直线导轨的磨损情况；



Check the abrasion pattern of the linear rail;



用棉布清洁直线导轨；



Clean the linear rail with a piece of cotton cloth;



用润滑油脂润滑直线导轨，从奶嘴处向滑块中加注润滑油脂。



Lubricate the linear rail with lubricant grease and fill the grease into the slider

from the nozzle.

3.3.7

Camera

Drive

X



取下 Camera Drive X 导向丝杆盖板；



Take

off the cover of Camera Drive X steering bar;



检查导向线杆磨损情况，用不起毛棉布清洁导向丝杆；



Check the abrasion pattern of the steering bar and clean

it

with a piece of lint-free

cotton cloth;



用 NSK 导轨丝杆专用润滑油稍加润滑导向丝杆；



Slightly lubricate the steering bar with NSK special lubricant for guid e rails;



用棉布清洁直线导轨；



Clean the linear rail with a piece of cotton cloth;



用润滑油脂润滑直线导轨，从奶嘴处向滑块中加注润滑油脂；



Lubricate the linear rail with lubricant grease and fill the grease into the slider

from the nozzle.



重新装好盖板。



Put the cover back.

德森精密机械设备有限公司

Shenzhen

DeSen

Precision

Machine

Co.,

Ltd

.

- 37 -

第四章常见故障分析与排除

Chapter

4

Common

Faults

and

Solutions

4.1

操作控制系统 Operation

Operation

Control

System

常见故障 Common

Faults

故障原因 Causes

排除方法 Solutions

开机后机器没有任何

动静：三色灯无指示、

计算机屏幕无显示

Machine has no

actions on start-up: tri

colour light has no

indications, and

computer displays

nothing.

1)

机器后面主电源开关未打开；

the main power switch not on

2)

总电源故障； main power

faults

3)

指示灯故障。 Indication light

error.

1)

打开电源开关； Turn on the

power switch;

2)

检查总电源开关及线路； Check

the main power switch and circuit ;

3)

更换指示灯。 Replace the

indication light.

设备不能启动

Equipment can ’ t be

started up.

1)

电控箱内的保险丝熔断； the

fuse in electric cabinet is burnt

out;

2)

其它故障。 Other faults.

1)

更换保险丝； Replace the fuse;

2)

按照计算机屏幕指示排除故障。

Remove the faults according to

indications on computer display.

计算机启动不了

Computer can ’ t be

started up

1)

启动器里有软盘； a disc in

drive;

2)

操作系统故障，运行文件丢失

。

Operating system faults;

operating file cannot be found.

1)

将启动器里软盘取出；

Take

out

the disc from drive;

2)

重新安装机器操作软件。 Re-

install machine

’

s operating

software.

设备动作间断，一个流

程无法完成 Equipmen t

operation is

interrupted, failing to

finish one cycle.

1 ）相应的传感器失灵，可能是光

电开关上覆盖了灰尘所致。 The

corresponding sensor

malfunctions, it may be due to

photoelectric switch being

covered by dust.

1 ）将其擦拭干净即可恢复正常。 Ju st

clean it up

气缸没有动作 Cylinder

has no actions.

1)

空气压力不够； The air

pressure is not high enough;

1)

检查总气源压力； Check the

pressure of main air source;