德森印刷机说明书之使用手册2 - 第38页
德森精密机械设备有限公司 Shenzhen Shenzhen Shenzhen Shenzhen DeSen DeSen DeSen DeSen P re cision P re cision P re cision P re cision Machine Machine Machine Machine Co., Co., Co., Co., Ltd Ltd Ltd Ltd . . . . - 37 - 第四章 常见 故障分 析与排 除…
德森精密机械设备有限公司
Shenzhen
Shenzhen
Shenzhen
Shenzhen
DeSen
DeSen
DeSen
DeSen
Precision
Precision
Precision
Precision
Machine
Machine
Machine
Machine
Co.,
Co.,
Co.,
Co.,
Ltd
Ltd
Ltd
Ltd
.
.
.
.
- 36 -
Notes
Notes
Notes
Notes
: Do not stretch the belts during adjustment.
3.3.6
3.3.6
3.3.6
3.3.6
Camera
Camera
Camera
Camera
Drive
Drive
Drive
Drive
Y
Y
Y
Y
检查 Camera Drive Y 轴导向丝杆的磨损情况；
Check the abrasion pattern of the Camera Drive Y guide rail;
清洁并润滑导向丝杆；
Clean and lubricate the steering bar ;
检查直线导轨的磨损情况；
Check the abrasion pattern of the linear rail;
用棉布清洁直线导轨；
Clean the linear rail with a piece of cotton cloth;
用润滑油脂润滑直线导轨，从奶嘴处向滑块中加注润滑油脂。
Lubricate the linear rail with lubricant grease and fill the grease into the slider
from the nozzle.
3.3.7
3.3.7
3.3.7
3.3.7
Camera
Camera
Camera
Camera
Drive
Drive
Drive
Drive
X
X
X
X
取下 Camera Drive X 导向丝杆盖板；
Take
off the cover of Camera Drive X steering bar;
检查导向线杆磨损情况，用不起毛棉布清洁导向丝杆；
Check the abrasion pattern of the steering bar and clean
it
with a piece of lint-free
cotton cloth;
用 NSK 导轨丝杆专用润滑油稍加润滑导向丝杆；
Slightly lubricate the steering bar with NSK special lubricant for guid e rails;
用棉布清洁直线导轨；
Clean the linear rail with a piece of cotton cloth;
用润滑油脂润滑直线导轨，从奶嘴处向滑块中加注润滑油脂；
Lubricate the linear rail with lubricant grease and fill the grease into the slider
from the nozzle.
重新装好盖板。
Put the cover back.
德森精密机械设备有限公司
Shenzhen
Shenzhen
Shenzhen
Shenzhen
DeSen
DeSen
DeSen
DeSen
Precision
Precision
Precision
Precision
Machine
Machine
Machine
Machine
Co.,
Co.,
Co.,
Co.,
Ltd
Ltd
Ltd
Ltd
.
.
.
.
- 37 -
第四章 常见故障分析与排除
Chapter
Chapter
Chapter
Chapter
4
4
4
4
Common
Common
Common
Common
Faults
Faults
Faults
Faults
and
and
and
and
Solutions
Solutions
Solutions
Solutions
4.1
4.1
4.1
4.1
操作控制系统 Operation
Operation
Operation
Operation
Control
Control
Control
Control
System
System
System
System
常 见 故 障 Common
Faults
故 障 原 因 Causes
排 除 方 法 Solutions
开机后机器没有任何
动静 ： 三色灯无指示、
计算机屏幕无显示
Machine has no
actions on start-up: tri
colour light has no
indications, and
computer displays
nothing.
1)
机器后面主电源开关未打开；
the main power switch not on
2)
总电源故障； main power
faults
3)
指示灯故障。 Indication light
error.
1)
打开电源开关； Turn on the
power switch;
2)
检查总电源开关及线路； Check
the main power switch and circuit ;
3)
更换指示灯。 Replace the
indication light.
设备不能启动
Equipment can ’ t be
started up.
1)
电控箱内的保险丝熔断； the
fuse in electric cabinet is burnt
out;
2)
其它故障。 Other faults.
1)
更换保险丝； Replace the fuse;
2)
按照计算机屏幕指示排除故障。
Remove the faults according to
indications on computer display.
计算机启动不了
Computer can ’ t be
started up
1)
启动器里有软盘； a disc in
drive;
2)
操作系统故障， 运行文件丢失
。
Operating system faults;
operating file cannot be found.
1)
将启动器里软盘取出；
Take
out
the disc from drive;
2)
重新安装机器操作软件。 Re-
install machine
’
s operating
software.
设备动作间断，一个 流
程无法完成 Equipmen t
operation is
interrupted, failing to
finish one cycle.
1 ）相应的传感器失灵，可能是光
电开关上覆盖了灰尘所致。 The
corresponding sensor
malfunctions, it may be due to
photoelectric switch being
covered by dust.
1 ） 将其擦拭干净即可恢复正常。 Ju st
clean it up
气缸没有动作 Cylinder
has no actions.
1)
空气压力不够； The air
pressure is not high enough;
1)
检查总气源压力； Check the
pressure of main air source;
德森精密机械设备有限公司
Shenzhen
Shenzhen
Shenzhen
Shenzhen
DeSen
DeSen
DeSen
DeSen
Precision
Precision
Precision
Precision
Machine
Machine
Machine
Machine
Co.,
Co.,
Co.,
Co.,
Ltd
Ltd
Ltd
Ltd
.
.
.
.
- 38 -
4.2
4.2
4.2
4.2
运输系统： Transport
Transport
Transport
Transport
system
system
system
system
2)
气路管道漏气或堵塞； air pipe l
leakage or blockage;
3)
控制线路接触不良。 Control
circuit is under poor contact.
2)
检查空气过滤器及气路管道；
Check the air filter and air path
channel;
3)
检查控制该气缸的电磁阀的控制
电压和信号。 Check the control
pressure and signal of solenoid
valve of this cylinder.
常 见 故 障 Common
Faults
故 障 原 因 Causes
排 除 方 法 Solutions
PCB 进板停留在等待位置
PCB board loader stays
at the waiting place
1 ）运输导轨上已经有 PCB
板。
PCB board is on transport
guide rail.
1 ）将导轨上 PCB 板取出后重新操
作。
Take
PCB board out of guide
rail before another operation.
运输时间超时
Transportation time is
overdue.
1)
运输皮带打滑；
transportation belt is
skidding;
2)
运输马达故障或运输单元控
制故障。 Transport motor
faults or transport unit
control error.
1)
调整运输皮带松紧； Adjust the
transportation belt;
2)
检查运输电机。 Check the
transportation motor.
印刷完后 PCB 板没有
被释放 PCB board is not
released after printing.
1)
送入调宽马达驱动器的信号
信接触不良； The signal line
of feed-in width-adjusted
motor drive is under poor
contact;
2)
驱动器故障； drive faults;
3)
传输皮带松或皮带脱落；
Transportation belt is loose
or belt is off;
4)
运输马达故障； transport
motor is broken down;
5)
宽度调节超出极限。 The
width is adjusted over the li
1)
检查线路； Check the circuit;
2)
更换驱动器； Replace the drive;
3)
调整皮带松紧； Adjust the belt;
4)
维修或更换运输马达； Repair or
replace transport motor;
5)
检查极限传感器。 Check the limi t
sensor.