00194614-08 Trainingsdoku. SG X-Serie_X4i SW70x (AL2)_EN - 第354页
Component Handling Optional Extension on the Changeover Tables Changeover Table Student Guide SIPLACE X-Serie and X4I SW70x (AL2) 354 X Tabl e 10.1.4.1 X Table Increas ing and Re ducing the COT He ight 10.1.4.2 Increasin…
Component Handling
Changeover Table Setting the COT Height
353 Student Guide SIPLACE X-Serie and X4I SW70x (AL2)
Special fitting screw on the changeover table docking unit
Setting the COT Height
10.1.4 Setting the COT Height
The changeover table can be adjusted to any height between 830 and 950 mm by removing the two pins
from the hollow shafts, which hold the table plate.
Pneumatic diagram docking unit
Legend
1. Pneumatic cylinder for moving the cam disks. This
means that the changeover table plate will move
43mm horizontally and 20 mm vertically into the
machine.
2. Throttle valves for adjusting the speed of the
pneumatic cylinders (time adjustment). Adjustment is
made without the changeover table and should take
approx. 2 seconds for docking and undocking.
3. Pneumatic cylinders for ejecting the COT during the
undocking procedure.
4. 5/2 way valve for controlling the pneumatic cylinder.
5. Safety valve in case of electrical faults
NOTICE
Adjustment of the COT height is in general identical for S and X tables.
CAUTION
Always use the screwed eyelet to fix the table plate, irrespective of whether you want to raise
or lower the component trolley.
Component Handling
Optional Extension on the Changeover Tables Changeover Table
Student Guide SIPLACE X-Serie and X4I SW70x (AL2) 354
X Table
10.1.4.1 X Table
Increas ing and Re ducing the COT He ight
10.1.4.2 Increasing and Reducing the COT Height
► Fix the screwed eyelet in the center of the table plate.
► A second person should lift the aluminum plate for X tables.
► Raise the changeover table plate slightly and knock the pins out of the left and right hollow shafts.
► Move the table plate to the correct height.
► Put back the 2 cotter pins (2) into the drilling hole of the sleeve shaft.
► Now, COT height is adjusted.
Optional Extension on the Changeover Tables
10.1.5 Optional Extension on the Changeover Tables
Additional R eel Holder o f the X Table
10.1.5.1 Additional Reel Holder of the X Table
The X table has 40 feeder locations. However, the tape reel container can only accommodate 30 tape
reels. An additional tape reel holder is therefore provided for the X table, as an option.
Additional reel holder X table
X table - adjusting the machine height
Legend
1. Hole for the cotter pins
Component Handling
X Feeder General
355 Student Guide SIPLACE X-Serie and X4I SW70x (AL2)
X Feeder
10.2 X Feeder
General
10.2.1 General
X feeder - basic view
Performance :
Increased demand for speed at C&P20A head (Communication, dynamics 40ms for 4mm), Feeder
should not limit placement (communication, transport)
Precision :
Designed for smallest components currently on the market
Reliability:
Reliable drive system, "Closed loop" drive regulation, new mechanical interface, new electrical interface,
brushless DC motors, optimized gear
Flexibility :
Different pitches adjustable, "Hot swapping" possible, upgrade per firmware download possible with
station software, adaptable for "problematic tapes", free step width, variable speed profiles
Usability :
Single track feeder, Tape loading, Interface to operator, Integrated Splice recognition (optional), Able to
handle sticky tapes (optional PSA kit (pressure sensitive adhesive)), no connectors and cables, operator
panel
Intelligence :
Unique feeder- ID, Management data (cycles, power up hours, errors,...), Object data are stored in set-
up control data base
Robustness :
No "on mechanical end stops" --> controlled movement of the transport