00194614-08 Trainingsdoku. SG X-Serie_X4i SW70x (AL2)_EN - 第459页
MTC2 Construction and mode of operation Installation of MTC 2 459 Student Guide SIPLACE X-Serie and X4I SW70x (AL2) Installati on of MTC2 13.2.6 Installation of MTC2 In the installa tion manual the modification is de scr…
MTC2
Modules of the controller Construction and mode of operation
Student Guide SIPLACE X-Serie and X4I SW70x (AL2) 458
Block diagram, sensors and actuators
Block diagram, sensors and actuators
Block diagram, sensors and actuators
MTC2
Construction and mode of operation Installation of MTC2
459 Student Guide SIPLACE X-Serie and X4I SW70x (AL2)
Installati on of MTC2
13.2.6 Installation of MTC2
In the installation manual the modification is described for a HF machine. The cables aren't available to
newer HF/HF3 and at the SIPLACE X machines at the side of the machine. All cables which go to the
docking frame are in the machine frame and must be attached according to the cable name.
The CAN Bus bridge is needed either at location 2 or 4, depending on the location at which you install
the MTC2.
Additional CAN Bus bridge for MTC2, if one wire bus has not been realized with a CAT5 cable
NOTICE
If you change the changeover table to an MTC2 at location 2 and/or 4 of a SIPLACE HF/HF3
or SIPLACE X machine, you will also need to change the whole docking unit (time needed
approx. 1 hour).
► Installation manual: Conversion of component trolley to MTC2 (00193897-01.pdf / German,
English)
NOTICE
The HF machines with the series number A 001 and the SIPLACE X machines are equipped
with a "One Wire bus" which is integrated in the Can bus. If you install an MTC2 on these
machines, you must bridge the CAN Bus cable before the docking frame of the MTC.
Reason: The wiring in the docking frame can transmit the CAN Bus signals but not the one wire
signals.
NOTICE
The CAN Bus link is necessary, if the one wire cable integrated into the CAN Bus cable. When
the One Wire Bus installed with CAT5 cable, the CAN Bus link is not necessary.
MTC2
General Work Before Starting the MTC2 Construction and mode of operation
Student Guide SIPLACE X-Serie and X4I SW70x (AL2) 460
General Work Before Starting the MTC2
13.2.7 General Work Before Starting the MTC2
▪ Setting the basic height
▪ Installing the safety cover for the lifting axis
▪ Docking
▪ Undocking
Placement Functions
13.2.8 Placement Functions
Main View wi th MTC2
13.2.8.1 Main View with MTC2
MTC2 - Pla cement Fun ctions
13.2.8.2 MTC2 - Placement Functions
In the toolbar of the main view, select the icon for the menu function Feeders .
The user interface will switch to the Empty tracks view, when the Feeders menu is called up for the
first time, after the station computer software has been started.
Select the icon for the MTC2 at location 2 or the icon for the MTC2 at location 4.
The Matrix-tray changer view will be shown for the selected location.
See also
13.2.8.3 "Matrix-tray changer" view (Example: location 2) [ ➙ 461]
13.2.8.1 Main View with MTC2 [ ➙ 460]
NOTICE
see User manual 00193634-01_de.pdf / 00193635-01_eng.pdf.
Main view of the SIPLACE HF with MTC2 at locations
and 4
Legend
1. "Feeders" view
2. MTC2 at location 4
3. MTC 2 setup, towers 1 and 2
NOTICE
The icon for the MTC2 at the relevant location is only displayed if an MTC2 is available there.
NOTICE
If a setup is available for an MTC2 , it will be displayed in the main view of the diagram for the
relevant MTC2 .
Select this to open the Matrix-tray changer view for the MTC2 at the selected location.