CP6的IO代码 - 第314页
2.3 Checking Errors Through Production Information (WC T ype) It is possible to check for the presence of feeder errors through daily maintenance, but this section explains how to check for such errors by inspecting the …
2.2 Film Take-up Reel Reverse Torque Check
(WC and MC Types)
If the top film take-up reel reverse torque is weak, the top film may not be taken up
normally.
Use a push-pull gauge to confirm the reverse torque is set normally (1 kgf), and if it is
under this amount replace the reel.
Push-pull gauge
1. Set the push-pull gauge onto the periphery of the top film take-up reel.
2. Press the gauge to the blue mark (1 kgf), and verify that the top film take-up reel
does not rotate.
If it does rotate, replace the top film take-up reel.
Film Take-up Reel Reverse Torque Check
Top film take-up reel
Take-up lever
Feed lever
1 kgf
mark
Caution : The take-up lever and the feed
lever should make contact with
each other during measurement.
CP6M8080
Z9064ALPJ5560
Push-pull gauge
CP6M8079
Part 8 Chapter 2 Feeder Maintenance
Edition 1.0 8-2-5 CP-6 Series Mechanical Reference
2.3 Checking Errors Through Production Information
(WC Type)
It is possible to check for the presence of feeder errors through daily maintenance, but
this section explains how to check for such errors by inspecting the feeder through the
production information managed by the MCS.
Data required for feeder inspection
Compile the production data, and select MAINTENANCE.
Production Data (maintenance) – – – MAINTENANCE/DEVICE
Press the F1 key (select) and move the cursor to the desired device.
Production Data Display 1/2
MAINTENANCE - DEVICE
LINE : FUJI MC : CX0900 PROGRAM : Evaluation. W08xP02.D1
DATE : 96/03/21 09:11:02 - 96/03/23 00:00:00
D_NO. D_COMMENT
PARTS
ERROR
JUNK RATE 0 50 100%
001
resistor
2125T04. 1 20090 90 0 0.45
002
resistor
2125T04. 2 20000 0 0 0.00
003
resistor
2125T04. 3
20150 150 0 0.74
TOTAL 60240 240 0 0.39
(F1) (F2) (F3) (F4) (F5) (F6) (F7) (F8)
*----------------------------------------------------------------------------------------------------*
*----------------------------------------------------------------------------------------------------*
*----------------------------------------------------------------------------------------------------*
*----------------------------------------------------------------------------------------------------*
select
copla print
head nozzle error end
CP6M8081
Part 8 Chapter 2 Feeder Maintenance
Edition 1.0 8-2-6 CP-6 Series Mechanical Reference
Select the device with the cursor and press the F7 key (error).
The following information will be displayed.
Production Data Display 2/2
Refer to the error code display for information on the error codes shown in the dashed
frame.
When MAINTENANCE/DEVICE is chosen, and the device generating the error selected,
it is possible to check the detailed error information, which can be used to determine if
an inspection is required.
Caution : These error results also include errors due to defective part shapes and defective
parts tape. For this reason, you should check both feeder and parts for devices which
suffer from low operating rates.
ERROR CODE :
The following error codes are representative of pick-up errors. For other errors, check the
ERROR CODE DISPLAY.
12040403 No part in nozzle
1CA0A007-1CA0A009 Error due to on-end part during pick-up
12040407 Error due to angle offset during part pick-up
MAINTENANCE - DEVICE
LINE : FUJI MC : CX0900 PROGRAM : EVALUATION. WO8xP02.D1
D_NO.
001
D_COMMENT
: RESISTOR2125T04.3
1CA0A009 26
TOTAL 150
(F1) (F2) (F3) (F4) (F5) (F6) (F7) (F8)
*----------------------------------------------------------------------------------------------------*
*----------------------------------------------------------------------------------------------------*
*----------------------------------------------------------------------------------------------------*
*----------------------------------------------------------------------------------------------------*
ERROR CODE
ERROR
1CA0A008 40
1CA0A007 12
12040403
44
12040407
28
print
end
CP6M8082
Part 8 Chapter 2 Feeder Maintenance
Edition 1.0 8-2-7 CP-6 Series Mechanical Reference