00197195-02-UG SetupCenter 5.1_en - 第184页
Setup Verification in Practical Cases Working with X-Feeders Setting Up and T earing Down X-Feeders 184 User Guide SIPLACE Setup Center 5.1 From foil torn error in the station to the teardown status A further applica tio…
Setup Verification in Practical Cases
Setting Up and Tearing Down X-Feeders Working with X-Feeders
User Guide SIPLACE Setup Center 5.1 183
The teardown state remains even after the feeder has been removed or the station has been switched
off.
Teardown outside the station
Step 3
After you have released the button, the foil rocker must
be relaxed within 5 seconds (e.g. cut and foil or relax the
foil disposal rolls). The foil rocker must be in the upper-
most position.
NOTICE! If the foil rocker is still tensioned after
5 seconds, the tear down procedure will be canceled and
the system will assume that the button was pressed un-
intentionally.
Step 3
If the foil rocker is in the upper position, the tear down pro-
cedure has been completed.
▪ Feeder with LCD display
– The feeder display will show the state Reel re-
moved.
▪ Feeder with LCD display
– The pitch display LED will now switch back to its
original state.
In Setup Center the packaging unit to feeder relation is
deleted and the track is now shown as not verified. The
quantity can be printed.
CAUTION
Changing a tape without the teardown process
If a tape is changed in the station without using the feeder teardown process, Setup Center
does not receive any information about it. Traceability data could be faulty as a result of this.
So always initiate a tape change with the teardown process.
Exceptions:
If the setting Teardown after foil torn error (X-feeder) is activated in Setup Center, Setup Center
will be informed of the tape change.
Or, the option Tear down the packaging unit if the verification status of the X-feeder is unreliable
has been enabled at Tools => Settings => Line => Domain-Wide Verification Settings.
Step 1 (Starting situation)
The feeder is in the ready state.
Step 2
Unlock the feeder (1) mechanically and remove it from
the station. The feeder display or LCD display is off.
Setup Verification in Practical Cases
Working with X-Feeders Setting Up and Tearing Down X-Feeders
184 User Guide SIPLACE Setup Center 5.1
From foil torn error in the station to the teardown status
A further application case arises when a feeder with a foil torn error is to be torn down. This state can
also be displayed when a feeder has been torn down outside the current station.
Step 3
Cut the foils with a pair of scissors (1) and remove the
tape. The foil rocker will then be in the upper position.
Step 4
If the feeder is reinserted in the station and locked, the
display will show the status "foil torn".
▪ Feeder with LCD display
– The feeder display will show the state Torn foil.
▪ Feeder with LCD display
– The error state Torn foil is indicated by a red sta-
tus display and slow flashing of LED 2 of the pitch
display.
– On the 12/16 mm V2 feeder, the error state "Torn
foil" is indicated by a red status display and slow
flashing of LED 12 of the pitch display.
CAUTION! The feeder is in the Foil torn state.
The station is stopped because it is unable to differentiate
between an empty feeder and a torn foil.
You need to carry out the steps described below under
"From foil torn error in the station to the teardown status"
as described below.
Step 1
The feeder is in the Foil torn state.
▪ Feeder with LCD display
– The feeder display will show the state Torn foil.
▪ Feeder with LCD display
– The error state "Torn foil" is indicated by a red
status display and slow flashing of LED 2 of the
pitch display.
– On the 12/16 mm V2 feeder, the error state "Torn
foil" is indicated by a red status display and slow
flashing of LED 12 of the pitch display.
The foil rocker is in the upper position.
Setup Verification in Practical Cases
Tear Down After Foil Torn Error Working with X-Feeders
User Guide SIPLACE Setup Center 5.1 185
8.12.5.1 Setup Center Settings for X-Feeders and Their Effects
The following table shows what is to be carried out for the X-feeder depending on the Setup Center set-
ting.
8.12.6 Tear Down After Foil Torn Error
After a foil torn error, Setup Center can tear down a packaging unit. This prevents incorrect traceability
data from being written if an X-feeder has not been torn down properly and another packaging unit has
been put on the same X-feeder instead.
A torn foil error can occur if
▪ the foil is torn,
▪ the foil container is open,
▪ the foil has been cut through, or
▪ a tangled foil has not been transported properly.
Step 2
► Press the "Back" button of the feeder for at least 2
seconds.
NOTICE! If the foil rocker is not in the upper po-
sition after 5 seconds, it is assumed the button has been
pressed accidentally.
▪ Feeder with LCD display
– The feeder display will show the state Reel re-
moved.
▪ Feeder with LCD display
– After 0.75 seconds the error state "Torn foil" is de-
leted and the track is torn down. The status dis-
play turns green if the feeder module is needed
for the current placement job and if there is no
other error.
– The pitch display LED will now switch back to its
original state.
The feeder has been torn down.
The BACKWARDS button can now be released.
Tear down packaging unit after foil torn error (X-feeder) = OFF Tear down packaging unit
after foil torn error (X-feed-
er) = ON
Activate with verification = ON Activate with verification = OFF Complete setup verification
of track necessary
If the option Tear down the
packaging unit if the verifi-
cation status of the X-feeder
is unreliable has been ena-
bled at Tools => Settings =>
Line => Domain-Wide Verifi-
cation Settings, it is also
necessary to perform a
complete setup verification.
Activate via station
computer GUI
Activate with
reader
Activate via station
computer GUI
Activate with
reader
Activation not possi-
ble
Activation
possible
(with Scan
packaging
unit)
Activation possible Activation pos-
sible