00197195-02-UG SetupCenter 5.1_en - 第29页

Configuring Setup Center Settings of Offli ne Verification General User Guide SIPLACE Setup Center 5.1 29 Next setup 3.2.2 Settings of Offline Verification Here, you can activate /deactivat e the offline setup verificati…

Configuring Setup Center

General Settings of Online Setup Verification

28 User Guide SIPLACE Setup Center 5.1

Splice monitor

Settings Meanings

Action after missing re-

fill detection

None

Error handling with a splice monitor has been disabled. No action is needed.

Error handling with splice monitor

Error handling with splice sensor is activated.

Teardown packaging unit

The packaging unit needs to be torn down. Recommended setting to achieve

an enhanced and consistent process.

Action after missing

splice detection

None

Error handling with a splice monitor has been disabled. No action is needed.

Error handling with splice monitor

Error handling with splice sensor is activated.

% of original quantity to

detect missing splices

The option monitors splice sensors of S-feeders and X- feeders if the "Splice

detection" setting is activated for the component in the programming system.

If the quantity for a refilled packaging unit is undershot by the percentage val-

ue entered here, the track will be deactivated by Setup Center. The splice sen-

sor error has to be rectified in Setup Center and on the track.

The splice monitoring is activated if a value between 1% and 50% is entered.

The splice monitoring is deactivated if the value 0% is entered.

Please note that on the F-, S-, HF-, HS-, and C-series this setting only works

properly if the threshold value control is activated in the filling level control of

the station.

Settings Meanings

Teardown after foil torn

(X-Feeder)

If this setting is activated Setup Center cancels the relation between packag-

ing unit and feeder, in the event of an X feeder foil tear. Since the system is

unable to detect the replacement of a packaging unit in this error situation, this

setting ensures that the packaging unit is always rechecked after a foil tear.

This setting is always active if the option Tear down the packaging unit if the

verification status of the X-feeder is unreliable has been enabled at Settings

=> Line => Domain-Wide Verification Settings.

Enable quantity correc-

tion during refill

The quantity of the previous packaging unit can be corrected during refill. An

additional step on the scanner is necessary.

Configuring Setup Center

Settings of Offline Verification General

User Guide SIPLACE Setup Center 5.1 29

Next setup

3.2.2 Settings of Offline Verification

Here, you can activate/deactivate the offline setup verification. The following settings can be made:

3.2.3 General Settings for Setup Verification

Settings Meanings

Prepare next setup

The Next Setup icon is shown on the SIPLACE Setup Center user inter-

face. This icon opens the Next Setup view. This option requires a license.

External feeder LED

control

The status of the configured feeders at the station is shown on the feeder

LEDs.

The Next Setup view in SIPLACE Setup Center shows a list box with the fol-

lowing options:

▪ Station

▪ Preview

▪ Changeover

Behavior of the view

"Next Setup" after a job

download

The Next Download view is automatically closed or remains open after com-

pletion of the download.

Parameter Description

Active

Teardown after foil torn (X-

Feeder)

If this setting is activated Setup Center cancels the relation between

packaging unit and feeder, in the event of an X feeder foil tear. Since

the system is unable to detect the replacement of a packaging unit in

this error situation, this setting ensures that the packaging unit is al-

ways rechecked after a foil tear.

This setting is always active if the option Tear down the packaging

unit if the verification status of the X-feeder is unreliable has been en-

abled at Settings => Line => Domain-Wide Verification Settings.

Verify tray changers WPCs and MTCs are included in the offline setup verification.

Teardown changeover table

before verification

If this setting is activated, changeover tables that are to be used in a

new setup will be torn down automatically. If this setting is deactivat-

ed, these changeover tables will have to be torn down manually.

Check MSD level Activates the MSD verification (monitoring of moisture-sensitive com-

ponents) during offline setup verification. The MSD level specifies

how long moisture-sensitive components may be used for once they

have been taken out of their protective packaging.

Parameter Description

Allow Splicing of Alternative

Components

To allow splicing of alternative components you need to activate this

function in Setup Center.

You need to deactivate this option if you want to run alternative com-

ponents via a pre-setup feeder or complete packaging unit change on

the feeder.

Double check during refill (only

for packaging units with unique

ID)

When splicing a new tape reel the operator is prompted to scan the

preceding reel first and the new tape reel afterwards during scanning.

This function is only possible for packaging units with unique packag-

ing unit ID. This increases the safety during refill.

Configuring Setup Center

General Packaging Data for Station-Based Traceability

30 User Guide SIPLACE Setup Center 5.1

3.2.4 Packaging Data for Station-Based Traceability

Definition of packaging unit data which can be transferred to the station after successful verification (407,

505 or 605). You can define 6 different attributes.

► Select the required parameters from the relevant list boxes.

► Click on the Default Values button to apply the default settings coordinated with the SIPLACE Trace

Service.

3.2.5 Automatic Individualization of Batch Packaging Units

3.2.6 Print Current Quantity Barcode Label on Tear down

NOTICE

Packaging ID

In order for SIPLACE Trace Service Traceability to generate data, you need to have a Packag-

ing ID in attribute 6.

Parameter Description

Automatically individualize

packaging units of a batch

Setup Center supports identical component batches for linear feed-

ers and tray feeders. This means that the same unique ID can be

scanned for several linear feeders or tray feeders.

Select the required option:

On tray feeders

For linear feeders

Traceability (station based)

Copy the unique ID of the batch packaging unit into the batch field of

the packaging unit

Activate this option and the actually scanned unique ID is saved in

the batch field. Make sure that this is not also part of the barcode def-

inition. Access to the separate packaging units of the identical com-

ponent batches is not possible after tearing down, as these use

generated unique IDs.

Parameter Description

Active Setup Center supports printing the current quantity before tearing

down. This is useful in the operating mode "Identical component

batch", because the current packaging unit quantity is lost during tear

down. Quantity correction labels offer the possibility to keep this in-

formation. The quantity correction labels can be printed individually

for each packaging unit, for feeders, for tables and for the complete

setup during tear down (via GUI or scanner).

Print always The quantity correction labels are printed automatically during tear

down.

Ask operator before printing After tear down a prompt for printing the quantity correction labels is

displayed at the barcode scanner and in the Setup GUI. If printing is

requested, the printout is started.

Selected printer Printer on which the quantity correction labels are printed. The printer

must be configured in the operating system.

Barcode label template Setup Center supports specific templates for barcode labels.