QP341 351E规格书.pdf - 第14页
6. Parts Supply Units 6.1 Supply Units This section describes the supply units supported by the QP-341E. 6.1.1 Multi-Feeder Unit (MFU-6) (Optional) Mechanical IP-series and QP-242E feeders are supported by this unit whic…
5.3 Nozzle Station (Optional)
The following table details the available nozzle station selection.
Notes: Nozzle station type B is used if the two-camera system is used at the rear of the machine.
The capacity data may be subject to changes in line with development.
Large mechanical chuck specifications are under development.
Two sizes of mechanical chuck are available; small (S), and large (L). As illustrated
below, both chuck types can be used to grasp parts at opposing points on either the
longest or shortest sides. The maximum part dimensions that can be handled by each
chuck type for each pick-up method are detailed in the tables below.
The vertical extent of the point on the side of the part at which the chuck makes contact
(t2 in the figure above) must be within the range of 1 to 8.5 mm. Mechanical chucks
which handle parts that exceed the dimensions shown above, may not be suitable for the
nozzle station. Contact Fuji for details of nozzle station modifications.
a
➀
➁
57
45
10
10
17
17
bt1
S type
(mm)
a
➀
➁
74
74
20
20
17
17
bt1
L type
(mm)
b
a
➀
b
t1
t2
a
➁
a
: Contact points
QP3S013
Type
Nozzle station shape
Capacity
Nozzles
Nozzles
Mechanical chucks S
Mechanical chucks L
Nozzles
Mechanical chucks S
Mechanical chucks L
Mechanical chucks S
Mechanical chucks L
16
13
0
16
6
0
–
–
–
Further models and designs pending.
Other
QP3S012
A: Single cameraB: Two-camera
system
Custom solutions available.
– 10 – QP-341E-MM/QP-351-MM Specifications
Preliminary (January 10, 2000)
6. Parts Supply Units
6.1 Supply Units
This section describes the supply units supported by the QP-341E.
6.1.1 Multi-Feeder Unit (MFU-6) (Optional)
Mechanical IP-series and QP-242E feeders are supported by this unit which can
be used to perform batch changeovers. The tape index lever on IPC-type feeders
must be changed prior to use.
Refer to section 5.1 for details of feeder capacities.
Feeder setting conditions
Notes: Left side and right side refers to the feeder slots when viewed from the rear of
the machine.
1P, 2P etc. in the table indicates the number of pitches taken up by each feeder.
The number of neighboring slots taken up by each feeder setting is indicated in
parentheses.
Add one to the number of feeder pitches (e.g., 2P + 1P = 3P) when a Motor
Feeder is being loaded under the following circumstances.
• An 8 mm Motor Feeder, or an 8 or 12 mm IPC or BFC is loaded on the left
side of a 12 mm Motor Feeder.
• A 44 mm BFC is loaded on the left side of a 16 mm Motor Feeder.
• A 32 mm BFC is loaded on the left side of a 32 mm Motor Feeder.
• A 32 mm IPC is loaded on the left side of a 32 mm Motor Feeder.
Device table end-slot setting conditions
D1
D2
D3
D22
D23
D24
W8 W12 W16 W24 W32 W44 W56
Type 1 Type 2
W72 W88
QP3S015
#1: 56mm IPC and BFC feeders can be set at device position 2 (D2),
however 56 mm Motor Feeders cannot.
✓
✕
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✕
✕
✓
✓
✓
✓
✕
✕
✓
✓
✓
✓
✕
✕
✓
✓
✓
✓
✕
✕
✓ / ✕ (#1)
✓
✓
✓
✕
✕
✕
✓
✓
✕
✕
✕
✕
✕
✕
✕
✕
✕
✓
✓
✓
✓
✕
✕
✓
✓
✓
✓
✕
W8
W12
W16
W24
W32
W44
W56
1P(0)
1P(0)
2P(1)
2P(1)
2P(1)
2P(1)
3P(2)
3P (2)
4P (3)
1P(0)
1P(0)
2P(1)
2P(1)
2P(1)
2P(1)
3P(2)
3P (2)
4P (3)
2P(1)
2P(1)
2P(1)
2P(1)
2P(1)
3P(2)
3P(2)
4P (3)
4P (3)
2P(1)
2P(1)
2P(1)
2P(1)
2P(1)
3P(2)
3P(2)
4P (3)
4P (3)
2P(1)
2P(1)
2P(1)
3P(2)
3P(2)
3P(2)
4P(3)
4P (3)
4P (3)
2P(1)
2P(1)
3P(2)
3P(2)
3P(2)
3P(2)
4P(3)
4P (3)
5P (4)
Right side
Left side
W8 W12
2P(1)
2P(1)
2P(1)
2P(1)
2P(1)
2P(1)
3P(2)
4P (3)
4P (3)
W16 W24 W32 W44
3P(2)
3P(2)
3P(2)
3P(2)
3P(2)
4P(3)
4P(3)
4P (3)
5P (4)
3P(2)
3P(2)
4P(3)
4P(3)
4P (3)
4P(3)
4P(3)
5P (4)
5P (4)
4P(3)
4P (3)
4P(3)
4P(3)
4P(3)
4P(3)
4P(3)
4P(3)
5P(4)
5P(4)
6P(5)
4P(3)
5P (4)
W56
Type 1
2P(1)
2P(1)
2P(1)
2P(1)
2P(1)
3P(2)
3P(2)
4P (3)
4P (3)
Type 2
Type 1
Type 2
W72
W88
W72 W88
2P (1)
2P(1)
2P(1)
2P(1)
2P(1)
2P(1)
3P (2)
2P(1)
3P(2)
3P(2)
4P(3)
2P(1)
3P(2)
3P(2)
4P(3)
3P (2)
3P (2)
3P (2)
QP3S014
– 11 – QP-341E-MM/QP-351-MM Specifications
Preliminary (January 10, 2000)
6.1.2 Power Feeder Unit (PFU) (Optional)
NP-series and QP-132E Power Feeders are supported by this unit which can be
used to perform batch changeovers.
Refer to section 5.1 for details of unit holding capacities.
72 mm and wider Power Feeders, and stick feeders are under development.
Feeder setting conditions
Notes: Left side and right side refers to the feeder slots when viewed from the rear of
the machine.
1P, 2P etc. in the table indicates the number of pitches taken up by each feeder.
The number of neighboring slots taken up by each feeder setting is indicated in
parentheses.
Device table end-slot setting conditions
D1
D2
D23
D24
W8 W12 W16 W24 W32 W44 W56
Type 1 Type 2
–
–
–
–
W72 W88
–
–
–
–
–
–
–
–
–
–
–
–
QP3S017
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✕
✓
✓
✓
✕
✓
✓
✕
✕
✓
✓
✕
✕
W8
W12
W16
W24
W32
W44
W56
W72
W88
Type 1
Type 2
1P(0)
1P(0)
2P(1)
2P(1)
2P(1)
3P(2)
4P(3)
–
–
–
–
1P(0)
1P(0)
2P(1)
2P(1)
2P(1)
3P(2)
4P(3)
–
–
–
–
1P(0)
1P(0)
2P(1)
2P(1)
2P(1)
3P(2)
4P(3)
–
–
–
–
1P(0)
1P(0)
2P(1)
2P(1)
2P(1)
3P(2)
4P(3)
–
–
–
–
1P(0)
1P(0)
2P(1)
2P(1)
2P(1)
3P(2)
4P(3)
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Right side
Left side
W8 W12
1P(0)
1P(0)
2P(1)
2P(1)
2P(1)
3P(2)
4P(3)
–
–
–
–
W16 W24 W32 W44
1P(0)
1P(0)
2P(1)
2P(1)
2P(1)
3P(2)
4P(3)
–
–
–
–
W56
–
–
–
–
–
–
–
–
W72
–
–
–
–
–
–
–
–
W88
Type 1
–
–
–
–
–
–
–
–
–
–
–
Type 2
QP3S016
–
–
–
–
–
–
– 12 – QP-341E-MM/QP-351-MM Specifications
Preliminary (January 10, 2000)