FCM_User Reference Manual.pdf.pdf - 第158页
MIS User Re ference Manual 4022 5 91 96082 5-66 F CM Mult ifl ex 02.02 Er ro r co de Subsystem Error descripti on 44062 LAS Home err Phi area t oo lar ge 44064 Communication error on X servo 44065 Communication error on …
4022 591 96082 User Reference Manual
02.02 FCM Multiflex 5-65
MIS
Error code Subsystem Error description
41014 TC Unexpected board in runout - remove
41015 Init restart needed
41016 Stopper run-out does not work
41017 Error during erase flash PROM
41018 Flash PROM write protected
41019 Flash PROM full or defect
41020 Unknown error (TC AST60)
41021 Unknown error (TC AST61)
41022 Unknown error (TC AST62)
41023 Unknown error (TC AST63)
41024 Unknown error (TC AST64)
44032 LAS miss SMD after pick
44033 retain SMD after place
44034 lost SMD after align
44035 Vacuum level wrong
44036 Req X pos out of range
44037 Req Y pos out of range
44038 Req Phi pos out of range
44039 Power dip during MUP down
44040 Servo tracking err X axis
44041 Servo tracking err Y axis
44042 Servo tracking err Phi axis
44043 Servo power failure
44044 MUP/pusher down during move
44045 Undefined Error (LAS-26)
44046 Move when servo amp. disabled
44047 Move req while no homing done
44048 Zero EPD not found X axis
44049 Zero EPD not found Y axisd
44050 Zero EPD not found Phi axis
44051 Pusher down during move
44052 Index pulse X axis not found
44053 Index pulse Y axis not found
44054 Index pulse Phi axis not found
44055 PPU communication error
44056 Left stop X axis not found
44057 Front stop Y axis not found
44058 Home err Phi area too large
44060 X axis obstructed
44061 Y axis obstructed
MIS
User Reference Manual 4022 591 96082
5-66 FCM Multiflex 02.02
Error code Subsystem Error description
44062 LAS Home err Phi area too large
44064 Communication error on X servo
44065 Communication error on Y servo
44066 Communication err on Phi servo
44067 RS422 laser align link rcv. error
44068 Timeout communication X servo
44069 Timeout communication Y servo
44070 Timeout Communication Phi serv
44071 LAS RS422 laser align link xmit error
44072 Flash EPROM write protected
44073 Flash EPROM table full
44074 Suspected placement, check SMD
44075 Flash EPROM zero offsets lost
44076 Timeout Smart Feeder
44077 X pos out of range, offset/FFA
44078 Y pos out of range, offset/FFA
44079 misalign SMD
44080 MUP too slow
44081 MUP too fast
44082 PPU changed, associate?
44083 PPU changed, associate!
44084 Chuck not conform Action spec
44085 PPU cal. checksum error
44086 Laser sensor exchanged
44087 Data eeprom LA sensor corrupted
44088 X pos out of range due to LA comp.
44089 Y pos out of range due to LA comp.
44090 X pos out of range due to MUP comp
44091 Y pos out of range due to MUP comp
44092 X pos out of range due to XY comp.
44093 Y pos out of range due to XY comp.
44094 X pos out of range due to Pick off
44095 Y pos out of range due to Pick off
44096 X pick offset too large
44097 Y pick offset too large
44098 Phi pick offset too large
44099 SMD length not within req. limits
44100 SMD width not within req. limits
44101 SMD lost due to power down
44102 Align id not present (sys. error)
4022 591 96082 User Reference Manual
02.02 FCM Multiflex 5-67
MIS
Error code Subsystem Error description
44103 LAS Undefined Error (LAS-B8)
44104 Laser sensor not connected
44105 Laser measurement error
44106 Laser hardware error
44107 Laser protocol error
44108 Laser beam obstructed error
44109 Laser dirty error
44110 Laser checksum error on received data
44111 Laser time-out error on received data
44112 Laser parameter data damaged error
44113 Laser software error occured
44114 MUP did not move error
44115 LAS MUP has wrong notch size error
53307 BVM Measureline inconsistency
53790 BI Board id. configuration failed
53791 Barcode read failed
53792 Barcode read notification failed
53793 Board id. version not correct
53794 Param. save in param. file wrong
53795 Wrong configuration parameter
53796 Rate test startup failed
53797 Mailbox create failed
53798 Human interface not synchronized
53799 Human interface not started
53800 Close down failed
53801 Wrong AM id.
53802 No configuration entry found
53803 Time out
53804 Invalid response
53805 First board error
53806 Barcode not in range
53807 Board count failed
53808 No read was requested
53809 Barcode not matched in exist. order
53810 Validation of barcode not correct
53811 Barcode length not correct
53812 Illegal order handle
53813 Cannot start idle order
53849 BVM Fiducial/Badmark measurement failed
53850 DC Firmware SBIP timeout