Nordson-EFD-MeterMix-Guide - 第6页
6 Series 450 Autovalve Recommended Mixer: Series 160 Mixer The pneumatic Series 450 Autovalve is similar to the Series 400 Autovalve, except for the shut-off pistons which ensure good control of dot or shot volume. After…
5
Series 400HF Autovalve
Series 400 Autovalve
Recommended Mixer:
Series 160 Mixer
Manifold
Seat Plate
Valve Body
Tie Plate
Lip Seal
O-ring
Front Seal
Air Cylinder Body
With meter mix and dispense systems, the pneumatic Series 400 Autovalve is a
durable and reliable valve. The A and B shut off pistons have PTFE seals allowing high
ow with minimal maintenance as these seals can be adjusted without disassembly of
the valve body. The 9/16-18 uid inlet ports of the Series 400 Autovalve allows ow
rates of 3-4 gallons per minute, depending on pump capability and material viscosity.
7701895 400 Autovalve
Aluminum Valve, Single Air Cylinder, TPV Seals
Order handle separately; see Autovalve Accessories
for details.
MANIFOLDS FOR SERIES 400 AUTOVALVES
Ratio Part # (Manifold) Part # (Manifold with solvent port) Material Flow
1:1 7701933 7701935 Aluminum Low Flow
1:1 7701942 - Aluminum High Flow
Wide 7701946 - Aluminum High Flow
The 400HF Valve provides ow rates that are 15-30% greater than the standard 400
Valve conguration, without compromising accuracy or consistency. The large 3/4"
material inlet ports permit ow rates of 4-5 gallons per minute, depending on pump
capability and material viscosity.
ORDERING GUIDE
• Valve, manifold, and handle are ordered
individually
• For high back pressure conditions (i.e. over
1000 psi/69 bar) order a double air cylinder
• Seal Designations: T=PTFE, P=Polyurethane,
V=Viton, G=Polytuff
Specications 400/400HF/450
Valve
Size: 83.8l x 63.5w x 58.4h mm (3.3 x 2.5 x 2.3")
Body: 6061-T6 aluminum or 303 stainless steel
O-ring options*: Viton, PTFE, Ethylene-Propylene (E-P)
Lip seal options*: Viton, Polyurethane (PU), PTFE, Polytuff,
Ethylene-Propylene (E-P)
* Repair kits containing a complete set of lip seals and O-rings
are available.
Manifold
Size: 48.3l x 63.5w x 38.1h mm (1.9 x 2.5 x 1.5")
Material: 6061-T6 aluminum or 303 stainless steel
Outlet thread size options: 7/8"-14 (for standard bell mixers);
1 5/16"-12 (for oversized bell mixers)
Valve System
Weight: Aluminum valve and manifold: 1.6 lb (0.7 kg)
Stainless steel valve and manifold: 2.5 lb (1.1 kg)
Operating Parameters: Min. operating pressure: 5.5 bar (80 psi)
Max. fluid pressure: 240 bar (3500 psi)
Electric handle mount switch: 24V
Recommended Mixer:
Series 162A Mixer
Specications
See Series 400, above
7704105 400HF Autovalve
Aluminum Valve, Single Air Cylinder, TGT Seals
7701924 400HF Autovalve
Aluminum Valve, Single Air Cylinder, TPV Seals
Order handle separately; see Autovalve Accessories
for details.
6
Series 450 Autovalve
Recommended Mixer:
Series 160 Mixer
The pneumatic Series 450 Autovalve is similar to the Series 400 Autovalve, except for
the shut-off pistons which ensure good control of dot or shot volume. After each shot,
the dual pistons retract and “snuff back” material from the end of the mixing nozzle.
This feature helps eliminate “after drool.” This valve includes hard-coated and lubricated
pistons. It can be used either as a stationary head or hand-held unit. In addition, seals
can be adjusted without disassembly of the valve body.
Manifold
Seat Plate
Valve Body
Tie Plate
Lip Seal
O-ring
Air Cylinder Body
7702201 450 Autovalve
Aluminum Valve, Single Air Cylinder w/Snuff Back,
GT Seals
7702209 450 Autovalve
Aluminum Valve, Single Air Cylinder w/Snuff Back,
PV Seals
7702443 450 Autovalve
Stainless Steel Valve, Single Air Cylinder w/Snuff
Back, GT Seals
Order handle separately; see Autovalve Accessories
for details.
MANIFOLDS FOR SERIES 450 / 450RC / 450XT AUTOVALVES
Ratio Part # (Manifold) Part # (Manifold with solvent port) Material Flow
1:1 7702221 7702222 Aluminum Low Flow
Wide 7702224 - Aluminum Low Flow
1:1 7702541 - Stainless Steel Low Flow
Specications
See Series 400, previous page
7
Series 450RC Recirculating Autovalve
7702217 450RC Autovalve
Aluminum Valve, Single Air Cylinder w/ Snuff Back,
GT Seals
Order handle separately; see Autovalve Accessories
for details.
Manifold
Seat Plate
Valve Body
Tie Plate
Lip Seal
O-ring
Air Cylinder Body
Recommended Mixer:
Series 160 Mixer
The 450RC Autovalve allows continuous ow of material while still being able to
control shut-off at the mixer. Typical uses are for heated materials or materials with
llers that need to remain suspended. Gear pump applications can also benet
because pumps can be kept running while material is shut off at the mixer.
Recirculation occurring at the valve instead of the pump eliminates pressure buildup
in the lines, preventing off-ratio dispensing. The valve also incorporates a snuff-back
feature that minimizes or eliminates the possibility of material dripping or stringing
when the valve shuts off.
Manifolds:
See Series 450 Manifold Table, previous page
Series 450XT Snuff Back Valve
7702216 450XT Autovalve
Aluminum Valve, Extended Air Cylinder with Snuff
Back and GT Seals
Order handle separately; see Autovalve Accessories
for details.
Recommended Mixer:
Series 160 Mixer
This innovative dispense valve is designed specically for two-component urethanes and
eliminates exposure of wetted shafts to air. Since 2K urethanes are moisture sensitive,
any contact with air can cure the material, locking up the dispense valve.
Manifold
Seat Plate
Valve Body
Lip Seal
O-ring
Air Cylinder Body
Manifolds:
See Series 450 Manifold Table, previous page
Specications
Valve
Size: 132l x 63.5w x 58.4h mm (3.3 x 2.5 x 2.3")
Body: 6061-T6 aluminum or 303 stainless steel
O-ring options*: Viton, PTFE Ethylene-Propylene (E-P)
Lip seal options*: Viton, Polyurethane (PU), PTFE,
Polytuff, Ethylene-Propylene (E-P)
* Repair kits containing a complete set of lip seals and
O-rings are available.
Manifold
Size: 48.3l x 63.5w x 38.1h mm (1.9 x 2.5 x 1.5")
Material: 6061-T6 aluminum or 303 stainless steel
Outlet thread size options: 7/8"-14 (for standard bell mixers)
Valve System
Weight: Aluminum valve and manifold: 2.0 lb (0.9 kg)
Stainless steel valve and manifold: 3.4 lb (1.5 kg)
Operating Parameters: Min. operating pressure: 80 psi (5.5 bar)
Max. fluid pressure: 3500 psi (240 bar)
Electric handle mount switch: 24V
Specications Accessories
Weight: Aluminum valve and manifold: 1.6 lb (0.7 kg)
Stainless steel valve and manifold: 2.5 lb (1.1 kg)
Pressure Rating: 240 bar (3500 psi)
Polytuff, PTFE, Viton, and EP seals:
For varying chemical formulations and abrasive conditions
Optional Night Cap & Ratio Check Cap:
Available for 1:1 ratio manifolds