00197543-01_SM_JTF-S_ JTF-M_en - 第21页
Service Works 2.1.5 Control-Board JTF-M_Pos1100 [03111983-xx] and Control-Boa rd JTF- S_Pos1090[03111984-xx], Daughter Board _ Pos300 [0311174 4-xx] Service Manual SIPLACE JEDEC Tray Feeder 21 Daughterbo ard detail 1. J3…
Service Works
Interfaces / Communications / Magazine 2.1.5 Control-Board JTF-M_Pos1100 [03111983-xx] and Control-Board JTF-
20 Service Manual SIPLACE JEDEC Tray Feeder
2.1.5.1
2.1.5.1 Detailed description of control board and daughterboard
Detailed description of control board and daughterboard
Dip switches on control PCB
There are some Dip switches on the control PCB, which
are not used. They have to be set on Off (2):
▪ Dip-switch off (sink) (1), like shown in the picture.
Control board detail
1. U3 – EPROM
2. J2 – Host
3. J16 – Auxiliary power connector
4. J1 – Connector from Lemosa / FCU, will be connect-
ed to daughterboard and supplies power (30V/GND)
and signal (RX/TX).
5. U4 – Motor Driver IC [03111678-01] (Pos30 Mo-
tordriver IC U4 of control PCB_2034101)
6. U9 – Motor Driver IC [03111675-01] (Pos20 Mo-
tordriver IC U9 of control PCB_2033989)
7. U8 – Connector for J3 from daughterboard (control
signals)
8. JP1 – Converted power (24V/GND) will be supplied
from daughterboard (J2)
9. J9 – Serial RS232 (not used)
10. U12 – Feeder output bank
11. LED status bar U6
12. LED status bar U1
Service Works
2.1.5 Control-Board JTF-M_Pos1100 [03111983-xx] and Control-Board JTF-S_Pos1090[03111984-xx], Daughter Board _ Pos300 [03111744-xx]
Service Manual SIPLACE JEDEC Tray Feeder 21
Daughterboard detail
1. J3 – Control signals
2. J1 – from Lemosa / FCU
3. J2 – Converted power
Position daughterboard on control board
1. J3 connected to U8
2. J1 from Lemosa / FCU
3. Voltage converter from 30V Incoming to 24V Out-
coming
4. J2 connected to JP1
Service Works
Interfaces / Communications / Magazine 2.1.6 Magazine
22 Service Manual SIPLACE JEDEC Tray Feeder
2.1.6
2.1.6 Magazine
Magazine
2.1.6.1
2.1.6.1 No Magazine for SIPLACE JTF-S
No Magazine for SIPLACE JTF-S
(All compliant with the JEDEC standard. Publication 95 Page 4.10-12/D Reference JEDEC Standard No.
95-1, IEC 60286-5)
You can setup the SIPLACE JTF-S feeders with JEDEC-Trays with different heights:
SIPLACE JTF-S tray filling
The SIPLACE JTF-S can be filled directly (1) with JEDEC
Trays according the following standard:
1. Thin tray:7.62mm +/- 0.2mm
2. Thick tray:12.19mm +/- 0.2mm
Tray width 135.9 mm +0.25/- 0.13 mm
Tray length 322.6 mm +0.25/- 0.13 mm
Thin tray thickness 7.62 mm +/-0.2 mm
Thick tray thickness 12.19 mm +/-0.2 mm
Tray material The are trays made of plastic or opaque material (alu trays are optional).
Mass of tray 604 gramms / 1.33 lb
Tray flatness 0.800 mm over entire surface
SIPLACE JTF-S switch setting tray thickness
1. Depending on the used tray type (thickness), the
switch (1) must be set in the correct position.