YSM10安装调整(eng) - 第104页
For Ser v ice E n gineer Service Information SI1610004E -000= YSM10_Proced ures for the adjustmen ts required after installing a machine 104/107 9. Perform the “Lightness” adjustment for the side li ght continuously. Att…
For Service Engineer
Service Information
SI1610004E-000= YSM10_Procedures for the adjustments required after installing a machine
103/107
4. Select the head to be used for the adjustment.
When performing the adjustment for the main and the coaxial lights, use either of the 17mm sq. or
the 32mm sq. jig.
As the 32mm sq. milky white light adjuster is used for the adjustment of the side light, select the
head that a 304A(315A) can be attached.
Head numbers that a 304A(315A) can be attached
(For the machines with an ANC)
10-head type
5-head type
304A(315A)
2, 8
2, 5
Table 46
:
If the machine is NOT equipped with an ANC, attach the specified to the selected head. Make
sure that the type displayed on the window is the same as the actually used .
Caution:
Make sure that the attached to the head and the type displayed under the “Head number”
pull-down menu are the same.
As the length of the 304A (315A) and the 303A (314A) are different, if the adjustment is
performed with the different types (the type of the actual and the selected on the
window), it may cause an error in the measured result.
5.
[Move to Set Pos.] to pick up the light adjuster.
If the machine is equipped with an ANC, the of the head selected in step 4 is changed
to the selected , and the head moves to above the front-side feeder bank.
If the machine is NOT equipped with an ANC, the head to be adjusted moves to above the
front-side feeder bank. Put the machine into the “Emergency stop” state, and attach the
selected in step 4 to the head by hand.
6. Set the light adjuster to the .
Make the head suck the light adjuster with its light gray surface facing down.
7. [Execute] .
The following window appears. Make sure that the light adjuster is set properly, and
[OK]
to start the adjustment.
Figure 154
8. Perform the adjustment for the coaxial light continuously.
After saving the adjustment result of the main light, perform the lightness adjustment for the
coaxial light according to the instruction on the screen.
Figure 155
Make sure that the
type displayed
here and the actually
used are the
same.
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
For Service Engineer
Service Information
SI1610004E-000= YSM10_Procedures for the adjustments required after installing a machine
104/107
9. Perform the “Lightness” adjustment for the side light continuously.
Attach the milky light adjuster to the head and perform the adjustment.
Figure 156
10. Save the adjusted data.
When the adjustment is completed, a dialog box appears asking you to save the data.
Check if the values in the “Result” and “Bit” fields fall within the specification, and save the data.
If the values meet the specification, fill in the values on the check sheet.
Figure 157
<Specified value>
Light
Color of the Light adjuster
Tolerance of the measured value
Bit value
Main
Gray
Target value +/- 2
128 ~ 656
Coax
Side
Milky white
Table 47
[
]
When the Bit value does not meet the specification, check the following.
・ Is the correct jig (light adjuster) selected?
・ Is the jig (light adjuster) clean? If it is not, clean it with alcohol.
・ Is the lighting environment affecting the adjustment result?
・ Is the lighting condition normal? (Are all the LEDs lit?)
:
As the upper limit of the specified Bit value is the warning value, the adjustment is completed properly
even when the value exceeds the specified value.
If the measured result exceeds 656 (the 7/8 of the limit value), it may attribute to the deterioration of the
lighting device. It is recommended to replace the lighting. (Limit value of the Bit value: 750)
If the machine is equipped with the optional multi camera “6-DigitalMultiC”, perform the adjustment
for the camera continuously.
If the machine is not equipped with the optional camera, go on to step 14.
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/
For Service Engineer
Service Information
SI1610004E-000= YSM10_Procedures for the adjustments required after installing a machine
105/107
When the machine is equipped with a “6-Digital MultiC”
11. Select “6-Digital MultiC”.
Figure 158
12. Make the head suck the light adjuster with its light gray surface facing down.
13.
[Execute] .
Attach the light adjuster to the head according to the message and perform the adjustment.
14. Remove the light adjuster.
After completing the adjustment, press the [Emergency Stop]
and remove the light adjuster
from the head. Then [Vac. ON/OFF] to turn off the vacuum operation.
If the 304A (315A) (that the machine is not equipped with) was attached manually for the
adjustment, remove it and put the original back to the head.
该文档是极速PDF编辑器生成，
如果想去掉该提示,请访问并下载：
http://www.jisupdfeditor.com/