F4000N_revD.pdf - 第34页
F4000N Series Operating Manual Section 5: Point T ype & Function Reference Part # 562187N - 1 Rev . D Sep 201 2 33 © 20 12 Fisnar Inc. 1. F1 (Point Men u) Below is a list of fun ctions which are fo und under the F1/E…
F4000N Series Operating Manual
Section 5: Point Type & Function Reference
Part # 562187N-1
Rev. D Sep 2012
32
© 2012 Fisnar Inc.
SECTION 5: Point Type & Function
Reference
F4000N Series Operating Manual
Section 5: Point Type & Function Reference
Part # 562187N-1
Rev. D Sep 2012
33
© 2012 Fisnar Inc.
1. F1 (Point Menu)
Below is a list of functions which are found under the F1/ENTER key. These functions are
„point-type‟ functions, meaning that the values applied will occupy one memory address.
Please see SECTION 6:Sample Programs for additional programming examples.
1.1 Dispense Dot
Registers the current XYZ location as a dispense point for dot dispensing.
The dispense time and wait time must be set in a previous memory address by registering
a Point Dispense Setup instruction.
The upward motion of the tip after dispensing can be controlled by registering a Dispense
End Setup instruction and / or a Z Clearance instruction in a previous memory address.
Dispense End Setup and Z Clearance instructions are registered using the F4 (SETUP)
key.
See also SECTION 5:5.3 (Point Dispense Setup), SECTION 5:5.4 (Dispense End
Setup) and SECTION 5:5.5 (Z Clearance).
1.2 Line Start
Registers the current XYZ location as a Line Start point for line dispensing.
The line speed must be set in a previous memory address by registering a Line Speed
instruction using the F4 (SETUP) key.
Dispense delay times used at Line Start and Line End points can be controlled by
registering a Line Dispense Setup instruction in a previous memory address. The Line
Dispense Setup instruction is registered by pressing the F4 (SETUP) key.
See also SECTION 5:5.1 (Line Speed) and SECTION 5:5.2 (Line Dispense Setup).
F4000N Series Operating Manual
Section 5: Point Type & Function Reference
Part # 562187N-1
Rev. D Sep 2012
34
© 2012 Fisnar Inc.
1.3 Line Passing
Registers the current XYZ location as a Line Passing point. This is a location on the line
where the tip changes direction, such as at the corner on a rectangle.
1.4 Circle
Registers a circle, where the circle‟s center is at the current XYZ location. To register a
circle, jog the tip to the circle‟s center and press F1/ENTER, and then press the key 4 (for
circle). The display will prompt you to type the following data:
Diameter: Type the diameter of the circle and press ENTER.
Over Angle: (The value is from 1~360). After dispensing the circle, while going through
an extra part of the circle defined by the Over Angle, the dispenser will be
turned OFF.
Z Lift: 1. Yes 2. No
Selection: If you want the Z-axis (tip) to lift while going through the Over Angle, you
must select 1. Otherwise: select 2.
The speed must be set in a previous memory address by registering a Line Speed
instruction using the F4 (SETUP) KEY.
Dispense delay times used at the start of the circle and at the end of the circle can be
controlled by registering a Line Dispense Setup instruction in a previous memory
address. The Line Dispense Setup instruction is registered by pressing the F4(SETUP)
key.
See also SECTION 5:5.1 Line Speed and SECTION 5:5.2 Line Dispense Setup.
The upward motion of the tip after dispensing can be controlled by registering a Dispense
End Setup instruction and / or a Z Clearance instruction in a previous memory address.
Dispense End Setup and Z Clearance instructions are registered using the F4(SETUP)
key.
See also SECTION 5:5.4 Dispense End Setup and SECTION 5:5.5 Z Clearance.