F4000N_revD.pdf - 第45页
F4000N Series Operating Manual Section 5: Point T ype & Function Reference Part # 562187N - 1 Rev . D Sep 201 2 44 © 20 12 Fisnar Inc. 1.12.1 Brush Area: Rectan gle Brush Area Rectangle causes the tip to „paint‟ the …
F4000N Series Operating Manual
Section 5: Point Type & Function Reference
Part # 562187N-1
Rev. D Sep 2012
43
© 2012 Fisnar Inc.
1.12 Brush Area
The Brush Area command causes the tip to „paint‟ a defined area.
There are six Brush Area types: Rectangle, Circle, Rectangle 1, Rectangle Band, Circle
Band and Circle1. The next pages provide a detailed description of all the Brush area
types.
To register a Brush Area command, follow the instructions below.
Instruction
Display Shows
1
Press F1/ENTER to open the Point Menu
[POINT] 1/3
1 Dispense Dot
2 Line Start
.
.
7 End Program
2
Press X, to go to page 2
[POINT] 2/3
.
.
4 Brush Area
.
3
Press 4 to select Brush Area.
Brush Area Setup
------------------
1.Rectangle 4.Rect Band
2.Circle 5.Circle Band
3.Rectangle 1 6. Circle 1
Select:
4
Press the numeric key corresponding to
the brush area type then press ENTER
Brush Area Setup
------------------
1.Rectangle 4.Rect Band
2.Circle 5.Circle Band
3.Rectangle 1 6.Circle 1
Width(mm):
Band(mm):
5
Type the width value and press ENTER.
Type the band value and press ENTER.
Width and band values will be explained
further in this section.
F4000N Series Operating Manual
Section 5: Point Type & Function Reference
Part # 562187N-1
Rev. D Sep 2012
44
© 2012 Fisnar Inc.
1.12.1 Brush Area: Rectangle
Brush Area Rectangle causes the tip to „paint‟ the defined area by passing back and forth
along the X-axis, while moving the Y-axis a determined Brush Width distance after each
pass along the X-axis.
After registering the Brush Area Rectangle command, teach a Line Start point at the top
left corner of the area to be brushed and a Line End point at the bottom right corner of that
area (the tip will not dispense a straight line between these two points):
If, for example, a brush width of 5 mm was used, the tip will take the following path when
the program is run:
5 mm
5 mm
5 mm
5 mm
Line Start
Line End
Paint
Area
F4000N Series Operating Manual
Section 5: Point Type & Function Reference
Part # 562187N-1
Rev. D Sep 2012
45
© 2012 Fisnar Inc.
1.12.2 Brush Area: Circle
Brush Area Circle causes the tip to „paint‟ the defined area by following a spiral path from
the outside limit of the circle to the center of the circle. It works in reverse of the Circle 1
function.
After registering the Brush Area Circle command, jog the tip to a point on the outside limit
of the circle to be brushed and register that location as a Line Start point. Then jog the tip
directly across to the center of the circle and register that location as a Line End point (the
tip will not dispense a straight line between these two points):
If, for example, a brush width of 5 mm was used, the tip will take the following path when
the program is run:
An open or closed option is also available for this function. Selecting the Closed option will
make a whole circle first before making the spiral. Selecting the Open option will make the
spiral without closing the outer circle.
Closed Circle: Creates a circle first
then a spiral from the outside to the
center.
Line Start
Paint
Area
Line End
Open Circle:
Creates a spiral from the
outside to the center.