Service Manual HS60 - 第132页

5 Pn eum ati c Cutt er and E mpty-T ape Du ct S er vic e Manu al HS- 60 5. 2 P art s 03/ 200 3 US I ssue 130 5. 2 Part s All sp a re part s are li st ed in t he HS 60 spare part s catalogue, with their article numbers an…

Service Manual HS-60 5 Pneumatic Cutter and Empty-Tape Duct

03/2003 US Issue 5.1 Safety Instructions

129

5 Pneumatic Cutter and Empty-Tape

Duct

5.1 Safety Instructions

DANGER

The chapters "Operational Safety" in User Manual SIPLACE HS-60 and in this Service Manual

take precedence.

The machine SIPLACE HS-60 is powered by

219/380 V +/- 5% or

230/400 V +/- 5% or

239/415 V +/- 5% or

117/204 V +/- 5% or

133/230 V +/- 5%,

50/ 60 Hz line voltage

Portions of the system therefore conduct dangerous electricity. Inside the machine frame this is

true even while the master switch is turned off.

The machine has to be switched OFF and disconnected from the mains before you perform any

work in the area of the cutter.

In addition, the compressed air supply must be turned off at the main valve of the compressed air

unit in the machine frame and the compressed air lines must be bled by actuating the needle valve

on the compressed air unit.

Always secure the machine against unauthorized reactivation, as described in the User Manual,

chapter "Lock-Out and Tag-Out Procedure ...". 5

5 Pneumatic Cutter and Empty-Tape Duct Service Manual HS-60

5.2 Parts 03/2003 US Issue

130

5.2 Parts

All spare parts are listed in the HS 60 spare parts catalogue, with their article numbers and dia-

grams. 5

NOTE:

These instructions are only valid for the version 04 pneumatic cutter and the associated version

03 empty-tape duct.

One of the new features of cutter version 04 is a tape deflector which is installed over the movable

blade (see Fig. 5.4.2 -> 6). 5

5.3 Tools, Expendable Materials, Documentation

– Thick protective gloves

– Set of socket wrenches, cross-slotted screwdriver size 4,

– Open-end wrench, width across flats 10; slotted screwdriver size 1

– Torque wrench, Diagonal cutter, Sliding caliper

– Feeler gauge 0.05mm; 1.0mm; 1.5mm, 2.0mm; 2.50mm

– Straight-edge (for check of tape deflector)

– Mounting plate, Item no.: 00312731-01

– 2 large parallel clamps (or mounting plate, see above)

– Flat, sturdy work bench to fasten the removed cutter (or mounting plate, see above)

– Loctite no. 234, Item no.: 00334892-01

– Molykote paste, Item no. 02100335-01, 250 g, (preferred) or

ISOFLEX TOPAS NCA 52, Item. no. 00330850-01, tube 50 g

– Water-insoluble, fine-tip marker and a dry and clean cloth

– Current edition of SIPLACE HS-60 spare parts catalogue and SIPLACE HS-60 detailed circuit

diagrams

– SITEST program and current SITEST operating manual

– Current edition of „HS-60 Adjustment Instructions“ documentation

Service Manual HS-60 5 Pneumatic Cutter and Empty-Tape Duct

03/2003 US Issue 5.4 Overview of Mechanical Layout

131

5.4 Overview of Mechanical Layout

Fig. 5.4.1 Overview of Pneumatic Cutter Version 04 and Empty-Tape Duct Version 03