Service Manual HS60 - 第18页

1 Int rod uc ti on Se rvic e Manu al HS- 60 1.3 D ang er no tes 03/ 200 3 U S Iss ue 16 1.3 Dange r notes W ARNING 1 – A thorough know ledge of the relevant p art of this Service M an ual is requ ired before carrying out…

Service Manual HS-60 1 Introduction

03/2003 US Issue 1.2 Important notes on the Service Manual

1.2 Important notes on the Service Manual

1.2.1 Qualification and training of personnel

Personnel used for service must hold the relevant qualifications for the job. The user must keep

tight control over their responsibilities, assignment and supervision. Any employee who does not

have the relevant training must be trained and given appropriate instruction. If necessary the user

of the machine can have training provided by the manufacturer/supplier. 1

In addition, the user must ensure that the employees have fully understood the contents of the

service manual. 1

1.2.2 User classification

The operating software is structured so that certain functions or menus can only by used or called

by appropriately trained personnel. There are three different classes of user: 1

– operator,

– line engineer and

– service engineer.

Access to each class may be password-protected. 1

Operators 1

The operator class consists of any person who has been trained in operation of the machine.

These people are authorized to use any functions associated with operating the machine and may

call up any menus needed to use the machine. 1

Line engineers 1

Line engineers have undergone special training and are authorized to carry out line engineer ac-

tivities, such as creating set-up configurations, determining vision parameters, etc. 1

Service engineers 1

This class is intended for engineers from SIEMENSDEMATIC AG. They are trained to carry out

servicing work and to upgrade and retrofit the placement system. 1

1 Introduction Service Manual HS-60

1.3 Danger notes 03/2003 US Issue

1.3 Danger notes

WARNING 1

– A thorough knowledge of the relevant part of this Service Manual is required before carrying

out any work on the machine.

– All work must be carried out by appropriately trained and qualified personnel.

– All warning, caution and danger notes MUST be observed.

– In addition, read through Chapter 2 of the Service/User Manual carefully.

1.4 Liability of the manufacturer/supplier

We draw your attention to the fact that this service manual only contains descriptive and explan-

atory material and does not include any contractual conditions or undertakings. All obligations of

Siemens Dematic AG proceed from the conclusion of the contract concerned, under which you

have the machine described herein. This applies in particular to all statements regarding perfor-

mance or service life and the agreed liability for faults or defects. The provisions of the contract

regarding the liability for faults or defect are neither extended nor restricted by any statements in

this service manual. 1

1.5 Revision index

Manual Issue

First Draft

Provisional Service Manual 09/1998

First Version Service Manual HS-50 01/1999

Revision to Service Manual HS-50 07/2000

Revision to Service Manual HS-50 10/2000

Revision to Service Manual HS-60 03/2003

Service Manual HS-60 2 Operational safety

03/2003 US Issue 2.1 Safety instructions

2 Operational safety

2.1 Safety instructions

2.1.1 Conventions for the use of hazard symbols

This Service Manual contains notes that must be observed to guarantee your personal safety and

to avoid damage to equipment. These notes are highlighted by warning triangles and are indicated

as follows according to the level of risk:

DANGER or DANGER

as used in this Service Manual means that death, severe injury or considerable damage to equip-

ment will occur if the danger instructions are not followed.

WARNING or

as used in this Service Manual means that death, severe injury or considerable damage to equip-

ment may occur if the warning instructions are not followed.

CAUTION or

as used in this Service Manual means that slight injury or damage to equipment may occur if the

caution instructions are not followed.

NOTE

as used in this Service Manual provides information on the product or indicates a part of the Ser-

vice Manual that requires particular attention.

2.1.2 Qualified personnel

Qualified or adequately trained personnel means that these people are familiar with the setting up,

operation and maintenance of automatic placement systems and add-on devices and are suitably

qualified, e.g.

– have been trained, instructed or authorized to switch on and off, isolate, earth and identify elec-

trical circuits and system components in accordance with normal safety standards.

– have been trained or instructed in the upkeep and use of appropriate safety equipment in ac-

cordance with normal safety standards.

– have received first aid training.