Service Manual HS60 - 第19页

Se rv ice M a nu al HS-6 0 2 Ope rati on al saf et y 03/ 200 3 U S Iss ue 2.1 S afe ty in str ucti ons 17 2 Operational safe ty 2.1 Safety ins tr uction s 2.1. 1 Convent ions for the use of hazard sym bols This S ervice …

1 Introduction Service Manual HS-60

1.3 Danger notes 03/2003 US Issue

1.3 Danger notes

WARNING 1

– A thorough knowledge of the relevant part of this Service Manual is required before carrying

out any work on the machine.

– All work must be carried out by appropriately trained and qualified personnel.

– All warning, caution and danger notes MUST be observed.

– In addition, read through Chapter 2 of the Service/User Manual carefully.

1.4 Liability of the manufacturer/supplier

We draw your attention to the fact that this service manual only contains descriptive and explan-

atory material and does not include any contractual conditions or undertakings. All obligations of

Siemens Dematic AG proceed from the conclusion of the contract concerned, under which you

have the machine described herein. This applies in particular to all statements regarding perfor-

mance or service life and the agreed liability for faults or defects. The provisions of the contract

regarding the liability for faults or defect are neither extended nor restricted by any statements in

this service manual. 1

1.5 Revision index

Manual Issue

First Draft

Provisional Service Manual 09/1998

First Version Service Manual HS-50 01/1999

Revision to Service Manual HS-50 07/2000

Revision to Service Manual HS-50 10/2000

Revision to Service Manual HS-60 03/2003

Service Manual HS-60 2 Operational safety

03/2003 US Issue 2.1 Safety instructions

2 Operational safety

2.1 Safety instructions

2.1.1 Conventions for the use of hazard symbols

This Service Manual contains notes that must be observed to guarantee your personal safety and

to avoid damage to equipment. These notes are highlighted by warning triangles and are indicated

as follows according to the level of risk:

DANGER or DANGER

as used in this Service Manual means that death, severe injury or considerable damage to equip-

ment will occur if the danger instructions are not followed.

WARNING or

as used in this Service Manual means that death, severe injury or considerable damage to equip-

ment may occur if the warning instructions are not followed.

CAUTION or

as used in this Service Manual means that slight injury or damage to equipment may occur if the

caution instructions are not followed.

NOTE

as used in this Service Manual provides information on the product or indicates a part of the Ser-

vice Manual that requires particular attention.

2.1.2 Qualified personnel

Qualified or adequately trained personnel means that these people are familiar with the setting up,

operation and maintenance of automatic placement systems and add-on devices and are suitably

qualified, e.g.

– have been trained, instructed or authorized to switch on and off, isolate, earth and identify elec-

trical circuits and system components in accordance with normal safety standards.

– have been trained or instructed in the upkeep and use of appropriate safety equipment in ac-

cordance with normal safety standards.

– have received first aid training.

2 Operational safety Service Manual HS-60

2.1 Safety instructions 03/2003 US Issue

2.1.3 Use as prescribed

The product must only be used for its intended purposes as described in the catalogues and tech-

nical descriptions, namely the placement of SMD components, and only with the third-party equip-

ment and components recommended or permitted by SiemensDematic Use for a different or

extended purpose is not prescribed.

If the product is not used as prescribed, SIEMENSDEMATIC AG accepts no liability for any dam-

age that may occur and does not guarantee that the components will work properly and without

problems.

Use as prescribed also includes compliance with all the instructions in the user manual.

For the product to operate correctly and reliably, it must have been transported, stored, erected

and assembled correctly and must be operated and maintained with care.

2.1.4 Failure to use as prescribed

Failure to use the product as prescribed can result in both danger to life and limb and material

damage. For this reason any use that is not prescribed is not allowed. If the product is not used

as prescribed, SIEMENSDEMATIC AG accepts no liability for any damage that may occur and

does not guarantee that the components will work properly and without problems.

Examples of failure to use the product as prescribed:

– Placement of components that do not meet the permitted specification

– The use of component feeders that have not been approved

– The use of unauthorized accessories and additional modules

2.1.5 Important notes on operational safety

The following points MUST be observed in order to maintain operational safety:

2.1.5.1 General

Æ The operational safety of SMD automatic placement systems can be guaranteed only if the

system is used as prescribed and in accordance with the instructions in the User/Service Man-

uals.

Æ Always follow any safety regulations specific to your country.

Æ Make sure that the warning labels are always clearly identifiable and always easily readable.

Æ Replace any damaged warning or notice labels. Replace any labels that are missing.

Æ The machine key for releasing the covers on the machine must be kept in a safe place where

it is only accessible to qualified personnel.