00198705-01_AI_Portalmodularität_SX12_V3_DE_EN - 第101页
3 Fitting the Gantry 3.4 Installing the Gantry Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 101 Fig.28: Docking in at the gantry carrier 1. Docking hook on the …
3 Fitting the Gantry
3.4 Installing the Gantry
100 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020
Tilt guard on the gantry carrier
Fig.26: Tilt guard on the gantry carrier
The gantry is also fitted with a tilt guard (1)
on the gantry carrier.
CAUTION!
Tilt guard on the gantry carrier
When the tilt guard is open, the gantry
could fall off the gantry carrier.
Only open the tilt guard once you have
hooked the gantry carrier onto the
machine docking unit.
.
NOTICE
Tilt guard on the gantry
The tilt guard may need to be adjusted to the gantry type "standard gantry" or "40mm VHF
Twin gantry". For more details see the technical information "Description of correct pack-
aging for an SX gantry" [DE:TI2013‑05D06] [EN:TI2013‑05E06].
3.4 Installing the Gantry
Fig.27: Moving the gantry in
► (1) Use the gantry lift to move the
gantry in front of the machine location.
CAUTION!
Move the gantry carefully
Make sure that you do not hit the
gantry anywhere and do not move it
too far into the machine (2). Always
check the right and left sides.
.
3 Fitting the Gantry
3.4 Installing the Gantry
Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 101
Fig.28: Docking in at the gantry carrier
1. Docking hook on the gantry carrier
2. Docking unit on the machine linear
guides
► Move the gantry forwards so that the
gantry carrier docking hooks (1) are in
front of the machine docking unit (2).
► Always check the right and left sides.
Hooking the gantry carrier into place on the machine
Fig.29: Lifting the gantry
► Lift the gantry so that the gantry carrier
docking hooks (1) are above the
machine docking unit (2).
► Carefully lower the gantry so that the
two docking hooks (1) slide reliably into
the openings in the docking unit (2).
► Always check the right and left sides.
Fig.30: Docking hook hooked into place
The docking hooks are hooked into place on
the left (1) and right (2) sides.
The gantry carrier with the gantry is now
fixed reliably onto the machine.
3 Fitting the Gantry
3.4 Installing the Gantry
102 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020
Remove the tilt guard and move in the gantry
Fig.31: Opening the tilt guard
► Open the tilt guard (1).
► Push the gantry (2) into the machine so
that both sides of the gantry rest on the
two linear guides.
► Move the gantry lift with the gantry car-
rier out of the location.
Fig.32: Pulling the trailing cable
► Move the gantry (2) into the machine
so that the trailing cable (1) can be
pulled underneath, through the gantry.
Fig.33: Flat ribbon cable and pneumatic connections
► Carefully place the flat ribbon cable (1)
and the pneumatic connections (2) over
the gantry.
► Remove the black plastic foil. A cable
tie fixes the black plastic foil to the trail-
ing cable(3).