00198705-01_AI_Portalmodularität_SX12_V3_DE_EN - 第94页
3 Fitting the Gantry 3.3 Gantry Preparations 94 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 3.3 Gantry Preparations The gantry is packed in a transportation cra…
3 Fitting the Gantry
3.2 Preparations at the Machine
Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 93
Loosening the trailing cable
Fig.15: Taking the trailing cable out of the holder
► Loose the fixture screw (1) on the
holder (2).
► Carefully disconnect the trailing cable
(3) from its holder.
CAUTION!
Take care when handling the trailing
cable!
Take care not to damage the foil or the
trailing cable.
.
► Place the holder and the fixture screw
in the "Prepared case" for fitting back
into place later on.
Fig.16: Trailing cable forwards in the machine
► Take the trailing cable (1) and place it
carefully towards the front, into the
machine.
3 Fitting the Gantry
3.3 Gantry Preparations
94 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020
3.3 Gantry Preparations
The gantry is packed in a transportation crate. You need a gantry lift to transport the gantry.
3.3.1 The Gantry Lift
We recommend a gantry lift for transportation and assembly. Observe the following instructions:
WARNING
Installation
The installation can be performed manually, although we do recommend using a gantry lift
for safety purposes.
WARNING
Observe the manufacturer's operating guide!
Please consult the operating guide supplied for details of how to handle the gantry lift and
for all safety-relevant aspects. Observe the instructions therein
► Observe the safety instructions in the manufacturer's operating guide.
► Observe all safety instructions in this assembly guide when transporting and assem-
bling the gantry.
WARNING
Checks
► The operator is obligated to check the lifting assistance for visible damage at least
once at shift start or in case of an abnormality, anomaly or event and to give notice of
such damage immediately.
WARNING
Brake, wheels
► Lock the wheels by pushing the brake rod down/forward as far as possible before
loading or unloading the lifting assistance.
► Lock the foot brake after every moving procedure and/or after arriving the required
position in order to prevent inadvertent rolling of the lifting assistance. Release the
brake before moving it again.
WARNING
Stability, obstacles
► The platform must be always brought to the lowest position when using the lifting aid
as transportation unit (within the moving procedure). The load must always be
centered (in the center of gravity) on the platform (this may vary according to the indi-
vidual case) in order to achieve highest possible stability (tilt resistance) during mov-
ing. When moving the lifting aid, pay particular attention to obstacles such as door lim-
its, cables on the ground and also check the driving through height with the height of
the gantry lift slide. The small wheel diameter used (depends on configuration) could
mean that even smaller obstacles can cause an abrupt deceleration or inadvertent dir-
ection change if contact to the wheel is established.
► If the load is not completely lowered the lifting assistance may tilt or (in case of insuffi-
ciently secured load) the load may fall down depending upon driving speed and kind of
the obstacle. Thus, always lead the lifting assistance with appropriate speed, particu-
larly in curves and with changing or uneven soil conditions. Fasten the load always
sufficiently before transporting it in order to surely avoid inadvertent falling down and/
or reduce the transportation speed that also an unsecured load cannot glide from the
load pickup in case of an abrupt deceleration.
► Likewise the load must not come into oscillations during the transport . Thereby inad-
vertent reactions can occur.
3 Fitting the Gantry
3.3 Gantry Preparations
Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 95
WARNING
Fixtures
► Never loosen the fastening of loads, if these are still in use. Always ensure a safe
standing of the load before release it.
WARNING
Ergonomics
► Always make sure that the platform and the surface on which the load is putted down
and/or be taken up are on the same height (varies in case of individual preparations).
The load must be pulled of the platform and/or pushed onto it (not elevated/carried) in
order to work in an ideal ergonomic position!
WARNING
Risk of injury
► When using mobile (tiltable, swiveling, inclinable) load pickup devices always make
sure that no own or different parts of the body and also no other obstacles are to be
located in the entire movement range of load and load pickup devices.
Overview
Fig.17: Example of a gantry lift
1. Gantry lift (example)
2. Gantry carrier plate [03012160-xx]
CAUTION!
Safety instructions
Pay attention to the weight of approx-
imately 64 kg when unpacking the
transport wrapper!
Use appropriate tools or call further
qualified persons.
The gantry lift has to be locked suffi-
ciently when transporting it again in or-
der to eliminate any danger.
.