00198705-01_AI_Portalmodularität_SX12_V3_DE_EN - 第95页

3 Fitting the Gantry 3.3 Gantry Preparations Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 95 WARNING Fixtures ► Never loosen the fastening of loads, if these are…

3 Fitting the Gantry

3.3 Gantry Preparations

94 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020

3.3 Gantry Preparations

The gantry is packed in a transportation crate. You need a gantry lift to transport the gantry.

3.3.1 The Gantry Lift

We recommend a gantry lift for transportation and assembly. Observe the following instructions:

WARNING

Installation

The installation can be performed manually, although we do recommend using a gantry lift

for safety purposes.

WARNING

Observe the manufacturer's operating guide!

Please consult the operating guide supplied for details of how to handle the gantry lift and

for all safety-relevant aspects. Observe the instructions therein

► Observe the safety instructions in the manufacturer's operating guide.

► Observe all safety instructions in this assembly guide when transporting and assem-

bling the gantry.

WARNING

Checks

► The operator is obligated to check the lifting assistance for visible damage at least

once at shift start or in case of an abnormality, anomaly or event and to give notice of

such damage immediately.

WARNING

Brake, wheels

► Lock the wheels by pushing the brake rod down/forward as far as possible before

loading or unloading the lifting assistance.

► Lock the foot brake after every moving procedure and/or after arriving the required

position in order to prevent inadvertent rolling of the lifting assistance. Release the

brake before moving it again.

WARNING

Stability, obstacles

► The platform must be always brought to the lowest position when using the lifting aid

as transportation unit (within the moving procedure). The load must always be

centered (in the center of gravity) on the platform (this may vary according to the indi-

vidual case) in order to achieve highest possible stability (tilt resistance) during mov-

ing. When moving the lifting aid, pay particular attention to obstacles such as door lim-

its, cables on the ground and also check the driving through height with the height of

the gantry lift slide. The small wheel diameter used (depends on configuration) could

mean that even smaller obstacles can cause an abrupt deceleration or inadvertent dir-

ection change if contact to the wheel is established.

► If the load is not completely lowered the lifting assistance may tilt or (in case of insuffi-

ciently secured load) the load may fall down depending upon driving speed and kind of

the obstacle. Thus, always lead the lifting assistance with appropriate speed, particu-

larly in curves and with changing or uneven soil conditions. Fasten the load always

sufficiently before transporting it in order to surely avoid inadvertent falling down and/

or reduce the transportation speed that also an unsecured load cannot glide from the

load pickup in case of an abrupt deceleration.

► Likewise the load must not come into oscillations during the transport . Thereby inad-

vertent reactions can occur.

3 Fitting the Gantry

3.3 Gantry Preparations

Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 95

WARNING

Fixtures

► Never loosen the fastening of loads, if these are still in use. Always ensure a safe

standing of the load before release it.

WARNING

Ergonomics

► Always make sure that the platform and the surface on which the load is putted down

and/or be taken up are on the same height (varies in case of individual preparations).

The load must be pulled of the platform and/or pushed onto it (not elevated/carried) in

order to work in an ideal ergonomic position!

WARNING

Risk of injury

► When using mobile (tiltable, swiveling, inclinable) load pickup devices always make

sure that no own or different parts of the body and also no other obstacles are to be

located in the entire movement range of load and load pickup devices.

Overview

Fig.17: Example of a gantry lift

1. Gantry lift (example)

2. Gantry carrier plate [03012160-xx]

 CAUTION!

Safety instructions

Pay attention to the weight of approx-

imately 64 kg when unpacking the

transport wrapper!

Use appropriate tools or call further

qualified persons.

The gantry lift has to be locked suffi-

ciently when transporting it again in or-

der to eliminate any danger.

3 Fitting the Gantry

3.3 Gantry Preparations

96 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020

Assembly

Fig.18: Gantry carrier plate

Fitting the gantry carrier plate

To enable the gantry lift to accommodate the

gantry, the gantry carrier plate (2) must be

fitted to the slide (1) of the gantry lift.

► Use the four fastening screws (3) to fix

the gantry carrier plate(2) to the slide

(1) of the gantry lift.

 CAUTION!

Information on safety

Mount all eight screws with the associ-

ated washers and tighten them with

18Nm.