00198705-01_AI_Portalmodularität_SX12_V3_DE_EN - 第99页
3 Fitting the Gantry 3.3 Gantry Preparations Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 99 3.3.4 Transportation Locks and Tilt Guard Fig.25: Transportation lo…
3 Fitting the Gantry
3.3 Gantry Preparations
98 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020
Locking the gantry carrier correctly
Fig.23: Engaging the gantry carrier
► Check that the lever (2) on the lock (1)
has engaged properly.
► To open, press the lock backwards and
then press the lever downwards. This
opens the lock.
Securing the gantry in the transportation crate
Fig.24: Gantry secured
► The gantry is fixed with 4 screws (1) in
the transportation crate. Loosen these
screws.
CAUTION!
Only transport the gantry with the
gantry lift when the arms are locked!
.
► Move the gantry lift upwards and care-
fully lift the gantry out of the transporta-
tion crate.
NOTICE!
The placement head must be in the
center of the gantry.
This ensures that the load is distrib-
uted evenly during transportation.
.
3 Fitting the Gantry
3.3 Gantry Preparations
Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020 99
3.3.4 Transportation Locks and Tilt Guard
Fig.25: Transportation locks
The gantry is locked with three transporta-
tion locks (1) and (3) at the gantry carrier. In
addition, the head plate has two transporta-
tion locks (2) for the placement head.
CAUTION
Docking
► Flap down the transportation lock plates right before the docking.
► Make sure that the gantry does not slide off the gantry carrier during rerailing respec-
tively derailing and that the tilt guard is suspended in order to hold the gantry in posi-
tion.
► Move the green lever upwards and swivel the transportation lock to one side.
► There is another lever at (3). Move the green lever upwards and remove it.
► Loosen the two screws fastening the transportation locks (2) to the head plate in each case
and remove both locks.
NOTICE
Storing the transportation locks
If the gantry is transported or packed back into the transportation crate, you need to refit the
transportation locks.
► Place the transportation locks in the crate for later usage.
3 Fitting the Gantry
3.4 Installing the Gantry
100 Assembly Instructions / Montageanleitung SIPLACE SX1/SX2 V3 Gantry Modularity Portalmodularität 05/2020
Tilt guard on the gantry carrier
Fig.26: Tilt guard on the gantry carrier
The gantry is also fitted with a tilt guard (1)
on the gantry carrier.
CAUTION!
Tilt guard on the gantry carrier
When the tilt guard is open, the gantry
could fall off the gantry carrier.
Only open the tilt guard once you have
hooked the gantry carrier onto the
machine docking unit.
.
NOTICE
Tilt guard on the gantry
The tilt guard may need to be adjusted to the gantry type "standard gantry" or "40mm VHF
Twin gantry". For more details see the technical information "Description of correct pack-
aging for an SX gantry" [DE:TI2013‑05D06] [EN:TI2013‑05E06].
3.4 Installing the Gantry
Fig.27: Moving the gantry in
► (1) Use the gantry lift to move the
gantry in front of the machine location.
CAUTION!
Move the gantry carefully
Make sure that you do not hit the
gantry anywhere and do not move it
too far into the machine (2). Always
check the right and left sides.
.