00194103-01 - 第21页
User Manual SIPLAC E F5 HM 2 Operational safety Software Version SR.408.xx 03/ 2006 US Edition 2.1 Safety instructions 21 2 Operational safety 2.1 Safety instructions 2.1.1 Convention s for the use of hazard symbols This…
1 Introduction User Manual SIPLACE F5 HM
1.9 Abbreviations Software Version SR.408.xx 03/2006 US Edition
20
User Manual SIPLACE F5 HM 2 Operational safety
Software Version SR.408.xx 03/2006 US Edition 2.1 Safety instructions
21
2 Operational safety
2.1 Safety instructions
2.1.1 Conventions for the use of hazard symbols
This User Manual contains notes that must be observed to guarantee your personal safety and to
avoid damage to equipment. These notes are highlighted by warning triangles and are indicated
as follows according to the level of risk:
2
DANGER or
as used in this User Manual means that death, severe injury or considerable damage to equip-
ment
will
occur if the danger instructions are not followed.
2
WARNING or
as used in this User Manual means that death, severe injury or considerable damage to equip-
ment
may
occur if the warning instructions are not followed.
2
CAUTION or
as used in this User Manual means that slight injury or damage to equipment may occur if the
caution instructions are not followed.
NOTE
as used in this User Manual provides information on the product or indicates a part of the User
Manual that requires particular attention.
2.1.2 Qualified personnel
Qualified or adequately trained personnel means that these people are familiar with the setting
up, operation and preventive maintenance of automatic placement systems and add-on devices
and are suitably qualified, e.g.
– have been trained, instructed or authorized to switch on and off, isolate, earth and identify
electrical circuits and system components in accordance with normal safety standards.
– have been trained or instructed in the upkeep and use of appropriate safety equipment in ac-
cordance with normal safety standards.
– have received first aid training.
2 Operational safety User Manual SIPLACE F5 HM
2.1 Safety instructions Software Version SR.408.xx 03/2006 US Edition
22
2.1.3 Use as prescribed
The product must only be used for its intended purposes as described in the catalogs and techni-
cal descriptions, namely the placement of SMD components, and only with the third-party equip-
ment and components recommended or permitted by SIEMENS A&D. Use for a different or
extended purpose is not prescribed.
If the product is not used as prescribed, SIEMENS accepts no liability for any damage that may
occur and does not guarantee that the components will work properly and without problems.
Use as prescribed also includes compliance with all the instructions in the user manual.
For the product to operate correctly and reliably, it must have been transported, stored, erected
and assembled correctly and must be operated and maintained with care.
2.1.4 Failure to use as prescribed
Failure to use the product as prescribed can result in both danger to life and limb and material
damage. For this reason any use that is not prescribed is not allowed. If the product is not used
as prescribed, SIEMENS accepts no liability for any damage that may occur and does not guar-
antee that the components will work properly and without problems.
Failure to use the placement machine as prescribed includes, for example
– operation of the placement machine with safety equipment deactivated or removed.
– placement of components that do not meet the permitted specification.
– use of component feeder modules that have not been approved.
– use of unauthorized accessories and additional modules.
– use of the placement machine by unqualified personnel.
– operation of the placement machine without the hand guard (dummy feeder module) if not
every location is occupied with a feeder module or if a waffle-pack tray holder is used.
– unclear allocation of electrical connecting cables to each placement machine and the in-
stalled options (e.g. WPC, productivity lift).
– if there are two or more people standing at a component trolley location at the same time dur-
ing the retrofit.
2.1.5 Important notes on operational safety
The following points MUST be observed in order to maintain operational safety: