Printer 710_810 v8 Machine Control.pdf - 第31页
MACHI NE CONT ROL CAN BUS Chapter Issue 8 Oct 06 Technical Reference Manual 7.31 I/O Node 2 (Main Machine I/O) N2PL3 N2PL1 N2PL2 N2SK2 N2SK6 N2SK5 N2SK7 N2SK8 N2SK10 N2SK4 MAIN I/O NODE 2 181436 ISSUE N2SK9 N2SK3 Connect…
MACHINE CONTROL
CAN BUS
7.30 Technical Reference Manual Chapter Issue 8 Oct 06
I/O Node Boards CAUTION
ANTI-STATIC HANDLING.
Standard precautions must be adhered to when
handling electronic cards and configuring and inserting into the enclo-
sures.
The I/O Node Boards consists of multiple inputs and outputs, CAN encoder/
decoder and multiway connectors for machine components.
There are three I/O Node Boards fitted to a standard machine with a possible
one other board for the underscreen cleaner, if fitted, these are:
• I/O Node 1 - NextMove ES card (CAN master) located in the M36 Machine
Control Enclosure (standard)
• I/O Node 2 - Main Machine I/O board located at the rear of the machine
(standard)
• I/O Node 3 - Print Carriage I/O board located inside the print carriage
extrusion (standard)
• I/O Node 4 - Screen Cleaner I/O board located at the rear of the machine
(optional)
I/O Nodes 2 & 4 have a green (status) and a red (error) LED mounted on the
board. The status LED should flash twice periodically and the error LED should
not be illuminated during normal operation. The following table describes other
operations of the LEDs:
I/O Node 1 I/O Node 1 is the CAN master and is also known as the NextMove ES card
housed in the M36 Machine Control Enclosure. For more information, refer to
the M36 Machine Control Enclosure - NextMove ES Card section of this
chapter.
No of
Pulses
Red (error) LED Green (status) LED
Static Off No error Initialisation/Code execution stopped
1 Node ID from DIP switches is 0 CANopen NMT state is ‘pre-operational’
2 EEPROM contents invalid (EEPROM
empty/checksum error)
CANopen NMT state is ‘operational’
3 EEPROM access impossible (hardware
error)
CANopen NMT state is ‘stopped’
4 CAN controller switched to ‘bus-off’
mode
N/A
5 Firmware error N/A
6 Controller overload N/A
Static On Severe hardware/software error N/A
MACHINE CONTROL
CAN BUS
Chapter Issue 8 Oct 06 Technical Reference Manual 7.31
I/O Node 2 (Main Machine I/O)
N2PL3
N2PL1N2PL2
N2SK2 N2SK6 N2SK5 N2SK7 N2SK8
N2SK10N2SK4
MAIN I/O NODE 2
181436 ISSUE
N2SK9 N2SK3
Connector Description I/O
N2PL1 Power Input
N2PL2 CAN Signal In Input
N2PL3 CAN Signal Out Output
N2SK2 Vacuum Tooling Power/Grid-Lok Tooling Output
N2SK3 Tricolour Beacon Output
N2SK4
(Standard Machine)
Chase Clamps - Screen Clamps - Board Clamps - Board Stop
- Lid Bolt - Rail Board Stop - Cleaner Squeegee - Solvent Tank
Pressure
Output
N2SK4
(RTC machine)
Chase Clamps - Screen Clamps - Board Clamps - Rail Width
Clamp - Lid Bolt - Outroad Board Stop - Cleaner Squeegee -
Solvent Tank Pressure - Inroad Vane Lift
Output
N2SK5 Rising Table Brake Output
N2SK6 Internal Light Output
N2SK7 Air Pressure Sensor Input
N2SK8 Lid Bolt Extended Sensor Input
N2SK9 Vacuum Tooling Sensor Input
N2SK10 Screen Sensor Input
MACHINE CONTROL
CAN BUS
7.32 Technical Reference Manual Chapter Issue 8 Oct 06
N2PL1
N2PL2
N2PL3
Pin No. Signal Pin No. Signal
124V US 40V
20V 512V
324V SW 60V
4
1
6Way Trident Connector
(with pins)
Pin No. Signal Pin No. Signal
1N/C 6N/C
2CAN_L 7CAN_H
3CAN_GND 8N/C
4N/C 9N/C
5N/C
9Way DType Plug
1
6
Pin No. Signal Pin No. Signal
1N/C 6N/C
2CAN_L 7CAN_H
3CAN_GND 8N/C
4N/C 9N/C
5N/C
9Way DType Plug
1
6