Anleitung X2 SP 1 und 3.pdf - 第16页
2 Assembly instructions Special design for manual tray on X2 at loca tion 1 or 3 Special Design 04/2007 Edition 16 2.4 Deliverables – T ray holder for lo cation 1 or 3 (for 1 JEDEC tray) – 2 hexago n socket he ad screw M…
Special Design 2 Assembly instructions Special design for manual tray on X2 at location 1 or 3
04/2007 Edition
15
2 Assembly instructions
Special design for manual tray on X2
at location 1 or 3
2.1 Working principle
On an X2 it is possible to place a JEDEC tray inside the machine. 2
2.2 Requirements
2.3 Restrictions
The tray holder is intended solely for components that, including the tray, do not exceed: 2
– 0 mm to 13.5 mm (if two contact plates are installed)
– 3.5 mm to 16 mm (if one contact plate is installed)
in height. 2
If different components are to be placed on this tray holder, they must be no higher than this, oth-
erwise there is a risk of crashing with the head. 2
If a service tool is used, the machine must be set up with the standard set-up once more. 2
– Only a limited performance calculation is possible.
– Segment 2 of the TwinHead may not be able to reach every component in the tray, depending
where the tray holder / tray is positioned.
2
2
The restrictions concerning the component range still apply. 2
2
Hardware:
SIPLACE X2 with component trolley HF (S tables)
Software: SIPLACE Pro 3.0 or later
Station software >=601
2 Assembly instructions Special design for manual tray on X2 at location 1 or 3 Special Design
04/2007 Edition
16
2.4 Deliverables
– Tray holder for location 1 or 3 (for 1 JEDEC tray)
– 2 hexagon socket head screw M5 X 12 mm for tray holder
– 2 magnets for fixing the tray
– Carrier for second nozzle changer (03005337-xx)
– 1 Counter-sunk screw M5 x 12 mm
– 2 Adjust pins
Ø M6 x 14 mm
– 4 supports for nozzle changers 2.5 mm (03021044-xx)
– Programming guide for arbitrary carrier under SIPLACE Pro (00194607-xx)
– Assembly instructions for tray holders (00195382-xx).
2.5 Tools and consumables required
– Hexagon socket spanners, set
– Diagonal cutter
– Spirit level.
2
Special Design 2 Assembly instructions Special design for manual tray on X2 at location 1 or 3
04/2007 Edition
17
2.6 Safety instructions
WARNING
The safety instructions from the “Operational safety” chapter of the user manual and servicing in-
structions take precedence over these instructions. 2
The SIPLACE placement machines are supplied with main power voltage.
Consequently parts of these systems carry dangerous voltages! This voltage is present at certain
modules inside the machine base, even when the machine is switched off at the main power
switch.
Incorrect handling of the placement machine or touching live parts of the machine can result in
death or severe injury, and considerable damage to equipment.
BEFORE starting any work, shut down the operating system correctly, then switch the machine
OFF at the main power switch and disconnect from the main power supply. In addition, the com-
pressed air supply must be switched off at the compressed air unit's main valve in the machine
base and vented by actuating the needle valve on the compressed air unit.
There is DANGER for heart pacemaker wearers in the vicinity of the linear motors, as described
in detail in the "Special safety instructions for working in the vicinity of strong magnetic fields"
section of the user manual and service manual.
Always follow the accident prevention regulations, DIN or other standards and special safety
rules applicable in your country.
Pay attention to the information concerning residual voltages in the Operational Safety chapter.
Follow the ESD regulations as described in the operational safety section of the operating
instructions.
During the retrofit, always secure the machine to prevent access by other people and to prevent
it being switched on again. The procedure is described in the “Locking the machine…” section of
the user manual.
Working with the SITEST program further increases the risk of accident.
The SITEST program must only be used by authorized and trained personnel.
2
2.6.1 Definitions
2
Please note 2
2
2
2