ysm20r_cabpara - 第8页

14 6. Preconditions YSM20R (SESMK18400-00) v2.001 6.9 Re sale When the owner of the product is changed after r elocating or reselling the product described in t his specification or the product is relocating the product …

6. Preconditions

YSM20R (SESMK18400-00) v2.001

6. Preconditions

6.1 Effective area

This specification assumes that YAMAHA MOTOR Co., Ltd. (hereafter referred to as "YAMAHA") or an

association entrusted by YAMAHA is an interested party in Japan

In a foreign country outside Japan, the contract concluded by the overseas distributor and customer takes

precedence over this specification. So, the contents of this specification become the reference information.

6.2

Export control by the Foreign Exchange and Foreign Trade Control Law

Products and technologies described in this specification are applicable to the control defined in Japanese

Security Trade Control Laws, such as Foreign Exchange and Foreign Trade Control Law. So, such laws

should be observed strictly. Even when YAMAHA submits the Certificate of Non-Applicability (parameter

sheet) about the products and technologies described in this specification to your company, your company

shall be held responsible for judgement of the final non-applicability. Additionally, when the specifications

of the products and technologies described in this specification are changed or when the products or

technologies are built-into other products, this Certificate of Non-Applicability cannot be used.

6.3 Re-export control by the U.S. Government

The products, technologies, and software described in this specification may include U.S. origin products.

Therefore, the re-export control by the U.S. Government shall be observed strictly.

6.4 European region

To export the product to a European country, it is necessary that the product shall conform to the EC machine

directives and EMC directives (CE marking compliance).

For details, see "10.7 CE marking" described later.

6.5 Intellectual property right

The contents described in this specification explain the product specifications.

YAMAHA does not warrant or permit the operation of a third person’s intellectual property right or other

rights.

6.6 Industrial machine dedicated to indoor use

The product described in this specification is an industrial machine dedicated to indoor use. For operation of

the product, various detailed conditions that are described later shall be confirmed.

In particular, the descriptions regarding the safety shall be read thoroughly to strictly observe them.

6.7 Improvement

The contents described in this specification are subject to change without prior notice due to continual

improvement of the product or software.

6.8 Registered trademark

Microsoft, Windows, and Excel are registered trademarks of Microsoft Corporation in the United States and

/ or other countries.

6. Preconditions

YSM20R (SESMK18400-00) v2.001

6.9 Resale

When the owner of the product is changed after relocating or reselling the product described in this

specification or the product is relocating the product to another country, the after-sales service and warranty

contents become invalid afterwards.

If the after-sales support is required, the after-sales support service can be continued by concluding the

service contract with our company or one of our distributors.

6.10 Relocation

Please contact YAMAHA or your distributor prior to relocating the product to another country, even if the

product ownership remains unchanged. YAMAHA will investigate to determine the appropriate relocation

work, and will check to see how the relocation will affect the after-sales service and warranty content.

Please note that all after-service and warranty content becomes invalid if the product is exported to another

country.

If desiring a continuation of after-service in such cases, a new service contract must be made with the local

distributor.

6.10 Reproduction of documents without permission

No part of this specification may be reproduced (copied) without written permission of YAMAHA.

6.11 Establishment date

This specification describes the contents established as of September, 2018.

7. Preparations and installation

YSM20R (SESMK18400-00) v2.001

7. Preparations and installation

When the customer arranges a transportation company, be sure to thoroughly understand the

responsible area (conditions) and make the judgement.

See section "7.1" to "7.1.5", Responsible area when YAMAHA arranges the transportation company.

See section "7.2", Responsible area when the distributor or customer arranges the transportation company.

7.1

Responsible area when YAMAHA arranges the transportation company.

The transportation company designated by YAMAHA transports the product to the factory site designated by

the customer.

7.1.1 Unloading the product

To unload the product, the transportation company designated by YAMAHA unloads the product using heavy

machines, such as forklift, crane, and car gondola prepared by the customer.

If the customer is difficult to prepare heavy machines, contact YAMAHA at least one week before the

delivery date.

7.1.2 Transportation within factory site

To transport the product within the customer’s factory site, YAMAHA or the transportation company

designated by YAMAHA transports the product to the installation place at YAMAHA’s own risk. If the

customer unloads and transports the product for some reason, this shall be conducted at the customer’s own

risk.

7.1.3 Securing a delivery route

A delivery route necessary to transport the product is secured. In particular, securing of the opening width,

elimination of stepped portions, securing of the installation place, and relocation of other equipment are

conducted at the customer’s own risk. For details about the width of the opening, see "11. Major

specifications", 11.1 "Outline dimensions" described later.

7.1.4 Dew condensation prevention

To transport the product from a cold environment (about 10°C or less) to a temperature regulated

environment, such as clean room (about 20°C or more), it is necessary to install the product while gradually

balancing the product temperature so as to prevent dew condensation.

In this case, a temporary placing space suitable for the temperature balancing work needs to be secured.

However, when a truck with the temperature regulation function is used, this temperature balancing work is

not needed. When the customer requests this type of truck, YAMAHA will arrange it.

7.1.5 Collection of transportation tools and gears

After the transportation has been completed, the transportation company designated by YAMAHA collects

the waste packing materials, hand lifters, and curing materials.

On the delivery date, the transportation company’s staffs wait until completion of the production line startup

work (waiting at local site until 16:00).