00191174-01.pdf - 第81页

User’s Manual Test Program S ITEST 4 Mapping Software Version 10.xx Edition 03/98 4.1 Preparatory Steps for the M apping Operation 4 - 5 ● Select the Select gantry menu option a nd press the RE TURN key. The "S elec…

4 Mapping User’s Manual Test Program SITEST

4.1 Preparatory Steps for the Mapping Operation Software Version 10.xx Edition 03/98

4 - 4

NOTE

Each mapping plate is delivered with a diskette containing a measured values file. This file contains the

values of the deviation of the measuring points from their setpoint positions. These values are required for

PCB mapping for correction purposes. Following the input of the plate number (see below) the measured

values file is read in from diskette and only thereafter can the PCB mapping run be started.

●

Place the diskette supplied with the mapping plate into the floppy disk drive.

●

From the "PCB-mapping" menu select the

Mapp.-plate number

option and press the RETURN key. The

"Mapp.-plate number" input menu opens.

●

Enter the mapping plate number, confirm your entry by pressing the RETURN key and press the ESC key

to return to the "PCB-mapping" menu.

The measured values file associated with the mapping plate is read in.

The "Mapping run", "Mapping cont. run" etc. options can now be selected.

●

Select

Mapping run

function and press the RETURN key. The active gantry performs the mapping run.

After the mapping run is completed, the data determined will be automatically saved.

NOTE

On SIPLACE 80S machines it is good practice to select the

Mapp. both gantries

function instead of the

Mapping run

function so that the mapping run is performed for both gantries without

having to switch from

gantry 1 to gantry 2 (Select gantry). When the mapping run of gantry 1 is completed, gantry 1 is automatically

moved to the park position and subsequently the mapping run for gantry 2 is performed.

●

To review the mapping data determined, select the

Display mapping data

function and press the

RETURN key. The data determined are displayed on the screen.

NOTE

To increase the accuracy of the mapping run, the values measured are compared with each measuring

point (position). The maximum permissible deviation (delta) of the measured values determined during the

current measurement run must not be exceeded in comparison with the previous measurement.

When PCB mapping is completed, the number of the positions that did not comply with these require-

ments is displayed.

●

Press the ESC key three times to return to the SITEST main menu.

NOTE

The procedure described below is only required if on a SIPLACE 80S the PCB mapping procedure is per-

formed by means of the

Mapping run

function

rather than the

Mapp. both gantries

function.

CAUTION

∆

Move gantry 1 to the park position using the menu functions of the "Gantry positions" menu (see

section 3.5).

User’s Manual Test Program SITEST 4 Mapping

Software Version 10.xx Edition 03/98 4.1 Preparatory Steps for the Mapping Operation

4 - 5

●

Select the

Select gantry

menu option and press the RETURN key.

The "Select gantry" menu opens.

●

Select the

gantry 2 active

for gantry 2 and press the RETURN key.

●

Press the ESC key to return to the SITEST main menu.

NOTE

When switching from one gantry to the other make sure that the position of the mapping plate is not

changed.

●

From the main menu select the

Mapping

option and press the RETURN key.

The "Mapping" menu is displayed on the screen.

●

From the "Mapping" menu select the

PCB-mapping

function and press the RETURN key.

The "Mapping" menu is displayed on the screen.

●

Select the

Mapping run

function and press the RETURN key. The active gantry performs the mapping

run. When the mapping run is completed, the data determined will automatically be saved.

●

Remove the mapping plate for PCB mapping.

●

Press the ESC key twice to return to the SITEST main menu.

NOTE

Do not

terminate your SITEST program session, but subsequently perform PCB mapping and in the case of

SIPLACE 80F machines, also IC-mapping.

4 Mapping User’s Manual Test Program SITEST

4.1 Preparatory Steps for the Mapping Operation Software Version 10.xx Edition 03/98

4 - 6

4.1.2 RV-Mapping

NOTE

Prior to the performance of RV-mapping make sure that PCB mapping has already been carried out.

The SITEST program must not have been restarted following PCB mapping.

●

Carry out the preparatory steps as described in section 4.1.

Additional prerequisites are:

both gantries must be in the park position.

segment offset

and

PCB/component camera offset must already have been determined for both

gantries.

the calibration piece must be in the calibration piece pocket.

the calibration piece position must already have been determined.

on segment 1 of each revolver head a size 617 nozzle must be attached.

●

From the main menu select the

Mapping

option and press the RETURN key.

The "Mapping" menu is displayed on the screen.

●

Select the

RV-mapping

function and press the RETURN key.

The "RV-mapping" menu is displayed on the screen.

Overview of the Functions:

RV-mapping to perform the RV-mapping

Cont. RV-mapping to perform mapping in the continuous run mode until the continuous run is aborted

by pressing ESC

Display mapping data to display the mapping data determined

Mapping data ct. run to display the data determined in the continuous mapping run

Continue RV-mapping to continue mapping from the measuring point entered

Mapp. both gantries to perform the mapping run for both gantries of SIPLACE 80S

(MC-changeover is carried out automatically. The mapping run is first performed

for gantry 1, thereafter for gantry 2.)

●

From the "RV-mapping" menu select the

RV-mapping

function and press the RETURN key. The active

gantry performs the mapping run. The measured values are automatically stored after the completion of

this mapping run.

Mapping

Mapping mode

PCB-mapping

RV-mapping

IC-mapping

Read mapping file

RV-mapping

Cont. RV-mapping

Display mapping data

Mapping data ct. run

Continue RV-mapping

Mapp. both gantries