00191174-01.pdf - 第9页
User’s Manual Test Program S ITEST 0 Introduction Software Version 10.xx Edition 03/98 0.4 Program Operation 0 - 5 0.4 Prog ram Opera tion The SITE ST pro gram is a menu -controll ed progr am in whi ch the keys an d comb…
0 Introduction User’s Manual Test Program SITEST
0.3 Program Options Software Version 10.xx Edition 03/98
0 - 4
0.3 Program Options
The chart below provides a rough overview of the commissioning and servicing activities that can be perfor-
med using the menu options of the test program.
Commissioning /
Servicing Activity
Axis functions (chap. 3)
Functions of the Motor Control Board (chap.4)
Calibration of the Comp. Camera (chap. 4)
Calibration of the PCB-C amera (chap.4)
Measuring the Segment Offset I (chap.4)
Offset of the PCB Camera to Comp.camera (chap.4)
Measuring the Centering Offset (chap.4))
Calibrating of the Machine Zero Point (chap.4)
ICalibration of the IC-Camera
Offset IC-Camera to Comp.camera (chap.4)
Calibration of the Flip-Chip-Camera (chap.4)
Calibration of the Copl.Laser Module (chap.4)
Calibration of the Nozzle Changer (chap.4)
Mapping (chap.. 5)
Measuring the Pick-Up Positions of Tracks 1 and 120
Initial start-up XXXXXXXXXXXXXXX
Electrical adjustment X X
Head replacement XXXXXXXXXXXXXXX
PCB camera replacement X X
Component camera replace-
ment
XXXX X
IC-camera replacement X X
Flip-Chip-camera replacement X
Installation/Replacement
Coplanarity laser module
X
Nozzle changer replacement X
Incremental encoder replace-
ment
XXX
Replacement of support of
component table
X
Tab. 0.3 - 1 Inbetriebnahme-/Servicearbeiten
User’s Manual Test Program SITEST 0 Introduction
Software Version 10.xx Edition 03/98 0.4 Program Operation
0 - 5
0.4 Program Operation
The SITEST program is a menu-controlled program in which the keys and combination of keys have the
following functions.
-
Cursor keys serve to move the cursor bar within the active menu, to change the positioning path
↑ ↓ ← →
during the dynamic adjustment of the axes, and to move the gantry when the teach
functions are activated.
-
RETURN key serves to confirm a selection, to start up functions, to open submenus and to
accept entries (see note below).
-
ESC key serves to terminate a menu or a function.
After the ESC key has been pressed, the program returns to the higher-level menu.
-
Page down key
↓
changeover to error display and exiting from the error display screen
-
ALT+0 switches the monitor to the IC-camera of SIPLACE 80F
-
ALT+7 switches the monitor to the component camera of the active gantry
-
ALT+8 switches the monitor to the PCB camera of the active gantry
-
ALT+ switches the monitor to the Flip-Chip-Camera of SIPLACE 80F
-
ALT+9 switches the monitor back to the normal program mode
-
Numeric keys serve to change the step width during movement of the gantry using cursor
keys when the teach functions are activated
-
START button serves to turn on the control unit
(at input/output belt)
NOTE
If a value is changed or newly entered in an input menu, the entry must
be confirmed by pressing the
RETURN key
or the cursor key
↓
prior to exiting from the input menu as otherwise this new value will not
be accepted.
0.4.1 Traversing the Gantry With the Teach Function Activated
The teach function is automatically activated if, for example, the Teach position function is selected on the
"Teach position" submenu of the "Vision system" menu (see section 3.1.2).
●
If you wish to change the step size for traversing the gantry, actuate one of the number keys 0 through 9,
with the "0" key representing the smallest and the "9" key the largest step size.
●
To move the gantry actuate the cursor keys
↑ ↓ ← →
.
The direction arrows on the cursor keys correspond to the gantry’s direction of travel as seen from a posi-
tion in front of the machine viewing into the direction of travel.
0 Introduction User’s Manual Test Program SITEST
0.4 Program Operation Software Version 10.xx Edition 03/98
0 - 6
0.4.2 Selection of the Active Gantry
On the SIPLACE 80S machine type it is not possible to work with the SITEST program on both gantries
simultaneously. It is therefore required that one of the gantries be selected prior to the start of the activities.
●
Select the menu option
Select gantry
from the SITEST main menu and press the RETURN key.
The selection menu for gantry is displayed.
NOTE
If the SITEST program is started for a SIPLACE 80F, menu option "Select gantry" cannot be selected as
the 80F system has only one gantry.
●
Select the gantry on which you wish to perform the actions and confirm your selection using the
RETURN key.
The number of the active gantry is displayed in the lower right corner of the screen (e.g. "MC-ACTIVE:1"
for gantry 1).
●
Press the ESC key to return to the SITEST main menu.
Portal 1 aktiv
Portal 2 aktiv
Portal wählen