00198608-02_SM_CP20P2_Kunde_EN - 第46页

6 Aperture ring, holding circuit and silencer 6.1 Replacing the aperture ring/holding circuit/sealing disc 46 Service Manual SIPLACE SpeedStar (C&P20 P2) 01/2019 Parts – compressed air operation NOTICE The SIPLACE C&…

100%1 / 90
6 Aperture ring, holding circuit and silencer
6.1 Replacing the aperture ring/holding circuit/sealing disc
Service Manual SIPLACE SpeedStar (C&P20 P2) 01/2019 45
6 Aperture ring, holding circuit and silencer
See also
2 9.3 "Replacing the holding circuit board" [}71]
6.1 Replacing the aperture ring/holding circuit/sealing disc
Parts – vacuum operation
Fig.56: Aperture ring
1 03165750-xx Aperture ring assembly SIPLACE C&P20 P2 (including sealing disc and
cover)
2 03006234-xx O-Ring 40x1.5
3 03105638-xx Sealing disc C&P20P
4 --- Pins
5 --- Groove: this groove shows the position of the pin (4) for easier installation.
6 03165754-xx Cover assembly C&P20 P2
03110132‑xx Sealing gasket M4 (for cover)
6 Aperture ring, holding circuit and silencer
6.1 Replacing the aperture ring/holding circuit/sealing disc
46 Service Manual SIPLACE SpeedStar (C&P20 P2) 01/2019
Parts – compressed air operation
NOTICE
The SIPLACE C&P20P2 with compressed air mode had not been released by the time this
document was published.
► Contact the SIPLACE Service team for details.
Fig.57: Holding circuit
1 03005123Sxx Holding circuit - vacuum unit
2 03046689-xx O-ring 50x1.5
3 03005120-xx Sealing disc for SIPLACE C&P20
4 --- Pins
5 03043707-xx Silencer assembly C&P20
See: 6.2 "Replacing the silencer (venturi mode only)" [}50]
Equipment and tools
T07 03078400-xx Torque Screwdriver ESD 1.0-5.0 Nm
T78 03090019-xx Torque interchangeable blades 2.5 mm, hexagonal
T98 03171857-xx Torque Allen swap blade 1.5 mm TX10
C03 03082092-xx Cleaning Wipe, KM-Wipe
C05 --- Isopropanol
C06 00352931-xx SIPLACE clean sticks
C11 03078517-xx ISOFLEX Topas 5051 50ml
T --- Tools for removing/fitting and calibrating the placement head, if needed
(see also the service manual for your machine)
6 Aperture ring, holding circuit and silencer
6.1 Replacing the aperture ring/holding circuit/sealing disc
Service Manual SIPLACE SpeedStar (C&P20 P2) 01/2019 47
Preparation
► Remove the head from the machine. For details about removing and fitting the placement
head, refer to the service manual for your machine.
Fit the head on the head mount [03056231‑xx].
► Make sure that the component sensor protective cap is fitted.
1.1.3 "Safety instructions for the component sensor" [}6]
Removal
NOTICE
Description example
The description uses the example of the aperture ring. The procedure for the holding circuit
is the same. Any relevant differences will be mentioned explicitly.
Fig.58: Dismantling the cover and aperture ring
► Remove the fastening screw(1) (TX10)
and then take off the cover.
► Remove the three screws(2) (TX10)
fastening the aperture ring.
► Carefully lever the aperture ring off the
locating pins. Make sure that the O-ring
is not damaged.
Fig.59: Cleaning
► Clean the seat of the aperture ring with
a cleaning cloth, coated with isopro-
panol.
 CAUTION!
Do not use compressed air for
cleaning!
.