00198608-02_SM_CP20P2_Kunde_EN - 第70页

9 Boards 9.2 Intermediate distributor board for SIPLACE C&P20P2 70 Service Manual SIPLACE SpeedStar (C&P20 P2) 01/2019 9.2 Intermediate distributor board for SIPLACE C&P20P2 Fig.98: Intermediate distributo…

100%1 / 90
9 Boards
9.1 Replacing the intermediate distributor board (ID)
Service Manual SIPLACE SpeedStar (C&P20 P2) 01/2019 69
Installation
Fig.96: Fitting the board
► Fasten the board(1) with the four
bolts(2). Secure the bolts with Loctite
222.
Fig.97: Circuit board connector
► Restore all electrical connections to the
intermediate distributor.
Fasten the board connectors(1) with
two screws each (TX6, torque
0.2Nm).
► Follow the removal instructions in reverse order for further installation.
► Transfer the machine data for the station to the EPROM of the intermediate distributor.
9 Boards
9.2 Intermediate distributor board for SIPLACE C&P20P2
70 Service Manual SIPLACE SpeedStar (C&P20 P2) 01/2019
9.2 Intermediate distributor board for SIPLACE C&P20P2
Fig.98: Intermediate distributor board for SIPLACE C&P20P2 [03134908-03]
Connector [03134908‑03]
X1,X2 Flat ribbon cable to the head adapter X3 Power supply for star motor
X4 Test connector X8 Power supply for Z axis
X15 Valve for return unit X16 CAN bus
X16b CAN bus X17 Z axis light barrier down
X19 Holding circuit board X20 Power supply for ED distributor
X21 Diagnosis connector X22 Incremental encoder for star and Z
X23 Incremental Z axis X24 Fan
X25 Digital pressure control valve X26 CO sensor
X30 Diagnostic FPGA X31 KED stator ring
LEDs [03134908‑03]
H1 Return unit Amber
H2 3.3 V Green
H3 5 V Green
H4 15 V Green
H5 24 V Green
H6 30V Green
H7 5 V pressure control valve Amber
H8 Fan FAN Amber
H9 Fan error ERR Red
H10 EON error 24 V DP (ground PWRGD_Dp) Green
9 Boards
9.3 Replacing the holding circuit board
Service Manual SIPLACE SpeedStar (C&P20 P2) 01/2019 71
9.3 Replacing the holding circuit board
Parts
Fig.99: Holding circuit board
03130694-xx Board for holding circuit assembly SIPLACE C&P20 P2
Equipment and tools
T07 03078400-xx Torque Screwdriver ESD 1.0-5.0 Nm
T19 00318673-xx Wire cutter electronic size 110
T44 00386132-xx Torque screwdriver ESD 0.1-0,6 Nm
T47 00386253-xx Torque screwdriver ESD 0.4-1.0 Nm
T78 03090019-xx Torque interchangeable blades 2.5 mm, hexagonal
T98 03171857-xx Torque Allen swap blade 1.5 mm TX10
C08 00308458-xx Cable ties B=2.5mm, L=102mm Panduit
T --- Tools for removing/fitting and calibrating the placement head, if needed
(see also the service manual for your machine)
Preparation
► Remove the head from the machine. For details about removing and fitting the placement
head, refer to the service manual for your machine.
Fit the head on the head mount [03056231‑xx].
CAUTION
Do not damage or contaminate the camera lens system.
► Make sure that you do not damage or contaminate the camera lens system.
► Make sure that the component sensor protective cap is fitted.
1.1.3 "Safety instructions for the component sensor" [}6]