OM-1606-006w_GT-28x.pdf - 第153页

OM-1606 7-3 7. Maintenance MOL YNOC GREASE AP1 (NIPPON OIL CORPORA TION) or its equivalent Grease Names Makers DAPHNE M-No.1 Idemitsu Kosan Co., Ltd JOMO Lisonix Grease M No. 1 JAP AN ENERGY CORPORA TION COSMO MOL YBD GR…

100%1 / 235
OM-1606
7-2
7. Maintenance
7.2 Preparation for Maintenance
Preparation for Cleaning and Oiling
•
Rag (Extra Cloth)
Use a rag made of such material (cotton, etc.) that produces as less waste thread
as possible.
A clean rag must be used depending on a spot to be cleaned.
Notice
The remaining waste thread if any will cause the machine to break
down.
•
Alcohol
Do not use alcohol on unspeci ed locations.
•
Toothbrush
It is required for tape peeling section.
Use normal cotton swab or toothbrush on the market.
•
Air Gun
Do not use the air gun for any spots other than the specied ones.
If dirt and dust are dispersed, moving mechanisms, causing the tape feeder to
break down.
•
Vacuum Cleaner
If the suction hole of the vacuum cleaner is changed to a smaller one, some
spots can be cleaned more easily.
•
Cotton Applicator (SIGMA-G5 Main Machine Standard Accessory)
It is used for removing dirt stuck onto the sensor section.
•
Bamboo Probe (SIGMA-G5 Main Machine Standard Accessory)
It is used to remove dust stuck onto the sensor section.
•
Greasing Jig (SIGMA-G5 Main Machine Standard Accessory)
Grease is applied using this syringe type jig.
(When grease for one division on the gauge is injected, grease of 0.1 ml is
applied).
•
Greasing Jig Nozzle (SIGMA-G5 Main Machine Standard Accessory)
Grease is applied using this syringe type jig.
•
Grease
Use MOLYNOC GREASE AP1 (NIPPON OIL CORPORATION) or its
equivalent.
1005-002
OM-1606
7-3
7. Maintenance
MOLYNOC GREASE AP1 (NIPPON OIL CORPORATION) or its equivalent
Grease Names Makers
DAPHNE M-No.1 Idemitsu Kosan Co., Ltd
JOMO Lisonix Grease M No. 1 JAPAN ENERGY CORPORATION
COSMO MOLYBD GREASE No. 1 COSMO OIL LUBRICANTS
BEACON Q2 ESSO OIL
Gemico MD2 TonenGeneral Sekiyu K.K.
M5 GREASE 1 KYGNUS
TG1
0908-001
OM-1606
7-4
7. Maintenance
7.3 Maintenance Check List
7.3.1 Daily Maintenance in Each Section
Location to be Maintained
Work Working Tools Check
Name
Reference
Drawing
Suppressor Section Upper Surface
of Suppressor
FG2 Cleaning Vacuum Cleaner, Rag, Toothbrush
TG2
7.3.2 Weekly Maintenance
Location to be Maintained
Work Working Tools Check
Name
Reference
Drawing
Suppressor Section Chute FG3 Cleaning Rag, Alcohol
Suppressor
(Rear Side)
FG4 Cleaning Rag or Cotton Swab, Alcohol
Peeling Section FG5 Cleaning Cotton Swab or Toothbrush
Cover Tape Take-up
Section
Tape Guide
Roller
FG7 Cleaning Rag, Alcohol
Component
Discharging Section
Discharging
Outlet
FG8 Cleaning Air Gun
Splicing Detection
Unit Section
Tage Guide FG9 Cleaning Cotton Swab, Alcohol
Bamboo Probe (Accessory)
TG3
7.3.3 Quarterly Maintenance
Location to be Maintained
Work Working Tools Check
Name
Reference
Drawing
Tape Feed Gear
Section
Worm Gear FG10 Cleaning,
Lubrication
Rag, Bamboo Probe (Accessory),
Greasing Jig,
MOLYNOC GREASE AP1
Cover Tape Take-up
Gear Section
Flat End
Wheel,
Worm Gear
FG11 Cleaning,
Lubrication
Rag, Bamboo Probe (Accessory),
Greasing Jig,
MOLYNOC GREASE AP1
Suppressor Section Pick-up
Position
FG6 Check,
Adjustment
Feeder Adjusting Jig JG-0209
(Purchase separately)
TG4
0908-001