bnp-b2365(eng)b.pdf - 第165页

3. Setup 3 - 78 No. Abbr. Parameter name Details <For MDS-C1-SPM> F E D C B A 98765 4 3 2 10 nsno nosg plgo enco bit Meaning when set to 0 Meaning when set to 1 Standard 0 enco Encoder orientation invalid Encoder o…

100%1 / 399
3. Setup
3 - 77
No. Abbr. Parameter name Details
<For MDS-C1-SP/SPH>
FEDCBA98765 4 3 2 10
splg dplg ospcl
noplg
nsno nosg plgo
mago
enco
bit Meaning when set to 0 Meaning when set to 1 Standard
0 enco Encoder orientation invalid Encoder orientation valid 0
1 mago Magnetic sensor orientation invalid Magnetic sensor orientation valid 0
2 plgo PLG orientation invalid PLG orientation valid 0
3 0
4 0
5 0
6 0
7 0
8 nosg
No-signal detection type
(Always monitoring)
No-signal detection valid only in
position loop or orientation-mode
0
9 nsno No-signal detection valid No-signal detection invalid 0
A noplg
Constant monitor of PLG-Z phase
no-signal invalid
Constant monitor of PLG-Z phase
no-signal valid
0
B 0
C 0
D ospcl
Orientation speed clamp
motor speed setting
Orientation speed clamp
spindle speed setting
0
E dplg 0
Fsplg
This is used by Mitsubishi. Set to "0" unless particularly designated.
0
(Note 1) For bit0 to 2, do not set two bits or more to "1" at the same time.
(Note 2) BitD is valid only when MDS-C1-SPH is used.
(Note 3) Set 0 if there is no particular explanation for the bit.
SP037 SFNC5* Spindle function 5
<For MDS-C1-SPX/SPHX>
FEDCBA98765 4 3 2 10
enco
bit Meaning when set to 0 Meaning when set to 1 Standard
0 enco Spindle end PLG orientation invalid Spindle end PLG orientation valid 0
1 0
2 0
3 0
4 0
5 0
6 0
7 0
8 0
9 0
A 0
B 0
C 0
D 0
E 0
F 0
(Note) Set 0 if there is no particular explanation for the bit.
Parameters with an asterisk * in the abbreviation, such as OSP*, are validated with the NC power turned ON again.
3. Setup
3 - 78
No. Abbr. Parameter name Details
<For MDS-C1-SPM>
FEDCBA98765 4 3 2 10
nsno nosg plgo
enco
bit Meaning when set to 0 Meaning when set to 1 Standard
0 enco Encoder orientation invalid Encoder orientation valid 0
1 0
2 plgo PLG orientation invalid PLG orientation valid 0
3 0
4 0
SP037 SFNC5* Spindle function 5
5 0
6 0
7 0
8 nosg
No-signal detection type
(Always monitoring)
Monitoring only in position loop or
orientation-mode
0
9 nsno No-signal detection valid No-signal detection invalid 0
A 0
B 0
C 0
D 0
E 0
F 0
(Note 1) For bit0 to 2, do not set two bits or more to "1" at the same time.
(Note 2) Set 0 if there is no particular explanation for the bit.
Parameters with an asterisk * in the abbreviation, such as OSP*, are validated with the NC power turned ON again.
3. Setup
3 - 79
No. Abbr. Parameter name Details
<For MDS-C1-SP/SPH>
FEDCBA98765 4 3 2 10
oplp lmx iqsv
XFzs
dcsn lmnp pl80 sdt2 vfbs orm adin plg2 pftm alty
bit Meaning when set to 0 Meaning when set to 1 Standard
0alty
Deceleration stop during special
alarm invalid
Deceleration stop during special
alarm valid
0
1 0
2 pftm
Encoder feedback serial
communication invalid
Encoder feedback serial
communication valid
0
3plg2
Semi-closed pulse output signal ×2
invalid
Semi-closed pulse output signal ×2
valid
0
4 0
5 adin
Interpolation during thread cutting
invalid
Interpolation during thread cutting
valid
0
6 orm Orientation start memo invalid Orientation start memo valid 0
7 vfbs This is used by Mitsubishi. Set to "0" unless particularly designated. 0
8 sdt2 (Follows SP038/bitC setting)
Set output 2 to 2nd speed detection
output
0
9 pl80 MHE90K detector's 180 wave PLG 180 wave PLG other than MHE90K 0
A lmnp This is used by Mitsubishi. Set to "0" unless particularly designated. 0
Bdcsn
Dual cushion during acceleration/
deceleration valid
Dual cushion during acceleration/
deceleration invalid
0
CXFzs
Set output 2 to MP scale low (L)
speed mode
Set output 2 to zero speed output 0
DIqsv 0
Elmx
This is used by Mitsubishi. Set to "0" unless particularly designated
0
F oplp Open loop operation invalid Open loop operation valid 0
(Note) Set 0 if there is no particular explanation for the bit.
SP038 SFNC6* Spindle function 6
<For MDS-C1-SPX/SPHX>
FEDCBA98765 4 3 2 10
oplp lmx iqsv
XFzs
dcsn sdt2 vfbs plg2 pftm alty
bit Meaning when set to 0 Meaning when set to 1 Standard
0alty
Deceleration stop during special
alarm invalid
Deceleration stop during special
alarm valid
0
1 0
2 pftm
Encoder feedback serial
communication invalid
Encoder feedback serial
communication valid
0
3plg2
Semi-closed pulse output signal ×2
invalid
Semi-closed pulse output signal ×2
valid
0
4 0
5 0
6 0
7 vfbs This is used by Mitsubishi. Set to "0" unless particularly designated. 0
8 sdt2 (Follows SP038/bitC setting)
Set output 2 to 2nd speed detection
output
0
9 0
A 0
Bdcsn
Dual cushion during acceleration/
deceleration valid
Dual cushion during acceleration/
deceleration invalid
0
CXFzs
Set output 2 to MP scale low (L)
speed mode
Set output 2 to zero speed output 0
DIqsv 0
Elmx
This is used by Mitsubishi. Set to "0" unless particularly designated
0
F oplp Open loop operation invalid Open loop operation valid 0
(Note) Set 0 if there is no particular explanation for the bit.
Parameters with an asterisk * in the abbreviation, such as OSP*, are validated with the NC power turned ON again