00196932-02 SM S-Feeder Repair DE EN multilang - 第112页
7 3x8mm S-Feeder checking and adjusting worm ge ar 7.2 3x8mmS: Adjusting cur rent input via the worm play 112 SIPLACE S-Feeder Repair SIPLACE S-Förderer Reparatur 5. When in upper position, fold up the adjustable flap an…
7 3x8mm S-Feeder checking and adjusting worm gear
7.1 Overview: 3x8mmS worm gear test set
SIPLACE S-Feeder Repair SIPLACE S-Förderer Reparatur 111
7
7 3x8mm S-Feeder checking and adjusting worm gear
3x8mm S-Feeder checking and adjusting worm
gear
7.1
7.1 Overview: 3x8mmS worm gear test set
Overview: 3x8mmS worm gear test set
7.2
7.2 3x8mmS: Adjusting current input via the worm play
3x8mmS: Adjusting current input via the worm play
1. S-Feeder Motor Testbox with display of the current
consumption
2. Power supply
3. Adjustment for the worm game.
4. Extern junction box
5. 3x8mmS worm gear
NOTICE! The worm drive clearance is adjusted
by means of the adjusting device such that the rated cur
-
rent input value is being reached (measured with the test
-
er).
1. Swing the lever (black handle) upward.
2. Fold the track-adjusting jig downward.
3. Insert the drive assembly into the jig from the side.
The two centering pins of the drive assembly must slide
into the holes of the device!
4. Swing the lever (black handle) downward in order to ar
-
rest the drive assembly.
7 3x8mm S-Feeder checking and adjusting worm gear
7.2 3x8mmS: Adjusting current input via the worm play
112 SIPLACE S-Feeder Repair SIPLACE S-Förderer Reparatur
5. When in upper position, fold up the adjustable flap and
...
6. ... pull up the three pressing pins in the upper position
in order to fold the jig completely upward.
7. Heed the labeling (blue,green, red) and connect the
three motor cables to the connection box using the cor
-
rect color assignment.
Red → black connector 1
Green → black connector 2
Blue → black connector 3
Now the drives of the three tracks will be checked and ad
-
justed in consecutive order from left to right.
8. Loosen the two Allen screws (size 2.5) of the drive unit,
starting with the left track..
7 3x8mm S-Feeder checking and adjusting worm gear
7.2 3x8mmS: Adjusting current input via the worm play
SIPLACE S-Feeder Repair SIPLACE S-Förderer Reparatur 113
9. Turn ON the left track of the tester-> Switch 6/30V in
Position 6V and switch 1 under "tape drive" up.The switch
position 30V is suitable for endurance test.
10. Turn the knurled screw of the left track until the rated
current input of 60 - 120mA (11) has been reached.
11. .During one complete revolution of the index wheel,
the current consumption should be constant!
12. Keep the motor running AND in this position, fasten
the two Allen screws M3 (size 2.5) of the adjusted track
hand-tight . With the screws tightened, the tester must
continue indicating 60 - 120mA (11).
13. Check the motor running noise for constancy.
14. Turn the left track on the tester OFF (switch 1 down).
15. Finally check the clearance of the adjusted track: For
this purpose, press your finger gently touching against
one pin of the sprocket wheel´s the track and try turning it:
▪ There must be NOT ANY perceptible clearance in
both directions of rotation any longer.
▪ Otherwise repeat the adjustment process.
▪ The drive assembly has to be repaired if adjustment
should not be optimally possible.
16. Now perform testing and adjusting the middle track
(Switch 2 under "tape drive"). For this purpose, proceed
according to the description for the left track..
17. Now perform testing and adjusting the right track.
(Switch 3 under "tape drive"). For this purpose, proceed
according to the description for the left track.
This completes the adjustment and the drive can be re
-
moved.